SharkBite U860W25, White PEX-B Pipe-Potable Water, 1/2 Inch, 25 Ft

This is sharkbite which is a great brand and very good quality. I’ve been using this stuff for years without any issues.

Worked well for me on a do-it-yourself home plumbing project.

Durable excellent product but hard to unroll if you don't do it right. It's a bit stiff and hard to flatten out. When unrolling make sure to unrolling evenly and not twist it or you'll be fighting with it for hours. Good product for the price.

Started to use PEX about 4 years ago in the kitchen during a repair. Kind of funny because I had a new counter top installed and the sink was not lined up with the plumbing from 1964. I was going to call a plumber because I had the drain line, hot water, cold water and dishwasher all under the counter, then under the house in a crawl space was a nightmare of copper tubing with a million elbows (ok, maybe 20 or 30). I did my research and decided to use SharkBite and PEX to correct the issue. Just looked under the house last week and everything is holding up just fine and looks so neat, and no soldering in a cramped crawl space.Review of the tubing - this stuff is awesome! it comes in a roll but I had have no problem getting a fairly straight run out of it using clips hammered in to the wood joists. I use a PEX tubing cutter and never had a problem cutting. Use the de-burring tool and never had a problem using SharkBite joiners or the clamps. Hot water and cold water have had no effect that I can see in 4 years. I just recently replaced the copper tubing to two outside hose connections with this and it is so easy to work with and the flexibility of the tubing is awesome!Most definitely recommend.

Works well no leaks

Worked just fine. Just be aware that it's really, really locked into that circular shape it comes in. Does not want to lay flat in the wall like we want it to. Very stiff, took lots of extra time to get it into the shape it needs to be, plus it is putting a whole lot of tension on just one side of every fitting it connects to. Other than that it was just fine. I have not worked with the better quality stuff, but hard to imagine the pros are putting up with this much stiffness on everyday jobs. Lots of wasted time.

I'm not a plumber. I was replacing a crappy Bosch tankless hot water heater in my basement with a new Navien NR 180 A tankless. Originally I planned on just using the existing plumbing. It would have fit fine and taken me less than a couple of hours to install, but that plumbing had some serious design flaws. Like I said I am no plumber, but common sense tells me a pipe shouldn't branch off the main water line at a 90 degree elbow pass over the heater on the hot water outlet side turn 90 degrees to go 3 inches to the middle of the heater then turn 90 degrees to go to the bottom of the heater then turn 90 degrees to go to a scaling filter located below the heater then pass through to the outlet of the filter turn 90 degrees up 2 inches and then 90 degrees back 5 inches then, at last, turn 90 degrees up to the cold water inlet.That seems a little excessive on the 90 degree elbows, all of which were soldered 3/4" copper.Then the hot water came out of the hot water outlet through a flex line that hit a straight pipe in front of the heater till it hits a 90 degree turn going back towards the heater but 3" below the ceiling till it is hits another elbow going up to the ceiling into another elbow that leads back to the hot water line next to the cold water line till it hits two more elbows that climb in step fashion into a joist bay in the ceiling. My conclusion is that someone hired a plumber from a Dr. Seuss children's book and I couldn't live with it any more, but as I said I'm not a plumber and hate sweating copper pipes that are attached to wooden structures that are covered in highly flammable foam insulation that is sprayed into the bays and can't be removed.The only solution I could find was pex. I used 2 - sharkbite connectors and 2 Sharkbite 90 degree pipe supports and two sharkbite flex connectors and got rid of about 15 feet of copper pipe and 15 copper elbows. I was also able to locate the heater 7 feet closer to the bathrooms and kitchen. I had no problem finding the numerous youtube videos on how to install pex and use the sharkbite connectors. I went with the push fittings, because I only needed two of them to join the existing copper to the pex and two of them to connect nipples for the scaling filter and the hot water outlet. The tools for the crimping connectors are very expensive, while the only tools required for the push fittings is the tubbing cutter and the sharkbite deburrer/ gauge. I was surprised that none of the joints I created leaked at all.Now I have a clean looking hot water heater installation and no more Whoville plumbing.

I need a PEX replacement tubing for what is in my 27-year-old unit. This is exactly what I was looking for. There were a few reviews that questioned the quality. They did not get what I received. This is freeze resistant and I can use SharkBite insert or standard fittings. Excellent quality and PEX is the best to use. Will buy again, and again.