Rough Country 2" Red Aluminum Leveling Kit for 07-18 Chevy/GMC 1500-1313

The install was very easy after watching a video on You Tube. The video that I watched showed how to install without having to drop the upper ball joint. I was able to install with just very minimal work. It does require you have another person to pry the shock over while you align the bolt. Once you have the bolt up you can put the nut on and tighten it up. I did put the bolts in from the bottom up however they do come with nylon washer bolts that are supposed to keep them from backing out. I know there is a lot of people on here that have left reviews saying to never put the bolts in from the bottom. I have never had a problem with them backing out also the factory bolts are put in from the bottom up with clips that snap onto the shock. Those clips are the same thread as the bolts that come with the kit. The only problem with using the clips is they are too big and will hit the axles on the back bolt. Once you have bolted the shocks on the rear bolts on the shocks will be really close to the axles however, they don't hit the axle. This installation technique saves a lot of time and keeps you from having unbolt most of your suspension like the instructions say to. The really only big difference is your bolts will go in from the bottom instead of the top.

Great way to add height to the front of my Silverado. Almost perfectly leveled out my truck and was very easy to install! The red looks great as well!

Made the front a little stiff but over all great product did exactly what I was looking for and the red was perfect for my build fitment was great and the look was definitely there

Fast shipping easy to install. Great price and product.

I'm not an ASE Certified auto mechanic, but I am an A&P (Airframe & Powerplant) and I started working on cars, motorcycles, boats and airplanes when I was about 12. I'm 58 now and I have done a lot of auto-wrenching over the years. After reading Rough Countries instructions, watching their video, and other videos I found on the internet, I came up with my own plan, and then modified that plan bringing the install down to 20 minutes per side from almost 90 minutes for the first side. On this truck the whole thing can be done in 40 minutes! It takes two people though. I did this with my 15 year old son. Instead of telling you what we did that was a waste of time, I'll tell you how the other side only took 20 minutes: Once the tire is off, loosen the bolt & nut that connects the lower control arm to the stabilizer bar. You do not have to remove it, just loosen the nut about 1/2" (it's on the top). Next, remove the bottom strut bolts and the clips, they connect the bottom end of the shock absorber to the lower control arm. It will pop loose and give you about 1/2" to 3/4" as the control arm drops away! But still not quite enough. Have your 15 year old son (or any small adult) stand on the top of the disc brakes and master cylinder. Just make sure they understand they need to be careful and not slip off and to stay away from the brake lines. Its wasn't difficult for my 15 year old son so any normal person should be able to do it. When he stood on it, the lower control arm dropped more than enough to slide the lift-blocks under the shock mounts. You will need to use a large screwdriver or pry bar to align the holes, but once you get the front bolt in, the rest is a piece of cake. A third set of hands at this point would make it easier too. Aligning the shock mount was physically the hardest part. Do the front bolts first. You may need to tap on the bolt with a hammer to get them started. Once through just put the nut on and tighten it until it starts to emerge from the nut. DO NOT TORQUE IT DOWN YET. Using your favorite method, cut (at least) 3/8" off the rear bolts before you install them, this is so they will not touch or interfere with the drive shafts. RC bolts are too long for the rear bolts on the 4wd trucks. You may have to remove and cut more off. The bolt should not extend beyond the nut for proper clearance of the drive shafts. The front bolts will stick out 1/2" but thats ok, there is nothing there to interfere. On a 2WD truck you probably don't have to cut them all because there is no front drive shafts. But on the 4WD like mine, they will touch the drive shaft and you cannot allow that. Now torque them, first to 35 foot-pounds, then re-torque them to 37 foot-pounds. Tighten up the stabilizer bolts to 35 foot pounds, put the tire back on and lower the truck. Repeat this procedure on other side. Have a front-end alignment done as soon as possible to avoid excessive tire wear from the new suspension-geometry. Check and re-torque your two bolts ever 500 miles as the manufacturer recommends, at least for a few thousand miles. If they never come loose you can probably extend that time but include those in your periodic checks and maintenance schedules. Especially if you offroad like we do.

In bought this for my 2019 new body style 1500. Follow the instructions and it's a simple install. The bolts have to go in with the head pointing up and the nut pointed down and they ARE exactly the proper length. It leveled my truck perfectly. I may add a 2 inch block in the rear though to make a cheap 2 inch lift kit. As it is now, on stock 265/65 18s I'm 3/4 inch shorter in front than a stock trailboss. I'll gain that 3/4 and then some going to a 33 inch tire. Very pleased. EDIT After alignment and settling in awhile this is still a great product and leveled the truck off nicely, but compared to stock only lifted the front end maybe an inch and a quarter. If you're trying to level then this is where it's at, but if you want an actual 2 inches, then look towards a strut top spacer. This only lifts the thickness of the spacer on the new Silverado

Quick shipping product as described happy customer

Perfect

Installation was easy! Fit perfectly. No issues since installed 3 months ago

Looks good fits perfect

Sits nice with the 2” Very easy to install, did it in my driveway Needed to purchase stronger nuts and bolts though

leveling works still a little off but for the money it’s worth it, made out of aluminum it’s really worth the money if you’re looking to level your truck

Fit my 2017 sierra perfect and got rid of the funky downward look. Leveled out nicely. Gave more clearance in front end. Just make sure you get a wheel alignment after installing