AZDelivery AZ-Nano V3-Board Mini USB Board Compatible with ATmega328 5V 16MHz CH340 ATmega328P Micro Controller, CH340G replaces FT232RL, Including E-Book!

Not the cheapest i could find however that being said after purchase i was sent a pdf of the operating instructions with diagrammes in colour which was a bonus also the nano comes in a proffesional colour diagramed box and the nano itself is inside in a antistatic bag.Now i no how to use them but if this is your first purchase of a arduino this is a very helpfull service so you can pretty much start right away with all the provided help,so for this reason alone i gave it 5 stars.

On the MacOsThis ARDUINO NANO needs to use an old bootloader called "Old Bootloader" which comes up in the list of selected items in TOOLS when the NANO is plugged in....... Not the "ATMegge328P Bootloader" , otherwise it functions the same as a UNO .Changing boards from UNO to NANO and back, it may need exiting from the ARDUINO IDE to get the USB to change over to the different board.After adding the Adafruit_ST7735 .h , GFH.h and TFT.h and TFTLCD.h libraries with LIBRARY manager.The Arduino AZ Adafruit ST7735 BREAKOUT ST7735 display runs from this version of the NANO.with#define TFT_CS 10#define TFT_RST 8 // Or set to -1 and connect to Arduino RESET pin was 9#define TFT_DC 9 // was 8and pinsST7735 NANO8. LCD. to 3.3V7 SCK to D136 SDA to D 115 A0 t o D94 RESET to 83 CS to D102 GND GND1 VCC 5V.

These were a replacement for three Elegoo Nanos that just failed out of the box.Unlike the Elegoo's Nanos, these were plug and play (already had the CH340 driver installed). Cost a couple of quid more, but worth it

The boards were delivered well packaged in a compact box.The PDF instructions were clear, which was good as I needed to refer to them after a few trial sketches failed to upload. This board uses the "old bootloader" (option selectable under tools, processor in the Arduino IDE). Once chosen everything worked smoothly. The USB drivers are included on OSX so no need to install anything other than the Arduino IDE for Mac users.I would recommend these boards

Beware - a misleading picture clearly shows one lot of three but you’re not buying one lot of three you’re buying one Nano.Instead of a good price each you’re getting a poor deal for one Nano with the CH340G chip. Much better prices elsewhere esp for multiples.

Does what it says on the tin. Instructions are not very clear though for what compiler or drivers you need however.

Very good price, and I like that the pins are included but not installed- I often want to wire direct. Useful for so many projects, and very easy to program.IMPORTANT- select (old bootloader) version in tools/processor - or it will not load!

Thought I was getting a great deal. Shows three boards in the picture. Add to basket and purchase. Only one shows up. This is right, just feels misleading from what is shown

Das AZDelivery 1x AZ-Nano V3-Board Set ist ein großartiges Mikrocontroller-Board mit dem Atmega328 und dem CH340 Chip. Die Qualität und die Verarbeitung sind wie immer bei AzDelivery top. Das Board lässt sich problemlos programmieren und funktioniert einwandfrei mit Arduino. Besonders hilfreich ist das mitgelieferte E-Book, das einem den Einstieg erleichtert.Die einzige Enttäuschung war die Anzeige, die etwas verwirrend war – ich hatte zunächst gedacht, dass ich drei Boards bekomme, aber es war nur eines. Trotzdem bin ich mit dem Produkt insgesamt sehr zufrieden, da es zuverlässig arbeitet und AzDelivery wie immer einen super Service bietet.

De beschrijving klopt, er is sprake van 1 module, echter is het misleidend om de zelfde afbeelding van 3 stuks weer te geven, als hun andere advertentie waar wel 3 items worden mee geleverd.Het is nog altijd mijn eigen fout dat ik niet had gelezen dat het slecht om 1 product ging, maar toch mag de foto aangepast worden op deze advertentie om het juiste aantal weer te geven.

El pedido fue todo perfecto,el arduino funciona perfectamente y el envío muy rápido, vendedor 100% recomendable

Utilisé avec SimHub dans mon cas, il n'a pas été aisé d'uploader les sketchs dans ces Arduino, obtenant systématiquement une erreur de communication avec la board, soit au dépôt du sketch, soit au moment de vouloir exploiter la carte.Après de nombreuses recherches, il s'avère que la puce Atmega328P CH340G nécessite un driver spécifique, que le fabricant distribue via la fiche produit, sur son site. Une fois installé, tout fonctionne parfaitement.Cherchez "AZ-Nano V3-Board avec ATMEGA328 CH340!" sur Google puis trouvez le lien "CH340 Treiber zum direkten Download" dans la page.

Precis så bra som man förväntat sig