chenyang 5 Pack USB C DIY Connector USB 3.1 Type C 24Pin Male Plug Port Repair Replacement Solder Adapter with PCB Board Black Housing

Everything came together well. Basic steps in photos:1. Put the body on the wire first. Then a flexible tail is put on the wire. Next, solder the wires to the connector. Check functionality.2. The inner case is pushed onto the metal part of the connector and beyond. The voids are filled with hot glue. Hint - apply hot melt adhesive in a thick layer around the green board and then push the inner case. Excess hot soft glue will be cut off by the inner case during the push-in.3. Slightly slide the inner case into the outer shell and apply a couple of drops of superglue on both sides and then push it all the way. A paper towel will come in handy to remove the extruded superglue.4. Done.5. In fact, the short cable is made for charging Garmin from a Samsung phone while traveling (Samsung, at least the S series performs the function of a power bank), but in this configuration, it is difficult to photograph if there is no mirror.

Emphasis on *device* as most breakout boards you'll find are configured as hosts. The difference, as shown, is the resistors: subdevice boards will have two 5.1kΩ resistors--one on CC and one on R1/R2 (labeling is inconsistent) while host boards have a single 56kΩ resistor on R2/R1. If you bought the wrong kind, you can always convert from one to the other if you're good with a soldering iron or have the kit for SMT work... or you could just buy the correct board to begin with, and if you're looking to convert a wired keyboard, wireless dongle or Webcam to USB-C, then **this is the listing to buy!**Bonus of this board is that the V+ and GND pads have contacts on both sides, giving you plenty of room to work.And yes, as the first picture shows, I did use this to build a webcam for the Steam Deck. It was completely plug & play on Linux, detected automatically on first plug in, and I've already started using this for telehealth appointments in Firefox running in Gaming Mode.

Work well, G and V pads are small though. the strain relief tube is too small for anything over say 28 AWG wire.

As far as the connector and electronics go it works. Had to figure out the correct order for the wires. My kid broke her usbc gaming mouse connector and I chose this to replace it. The wires were white, yellow, green, blue. Different than what I found online so I took apart the old connector to get that correct order. The plastic housing for this is complete crap. It doesn’t lock together and didn’t stay in place so the plug got pushed in and didn’t go into the computer. I ended up trying super glue but it didn’t stick to the plug. So I used instamorph moldable plastic to create a housing. Works great.

It took 3 to find one that worked. I could not verify if the resistor was actually 5.1k but it finally worked. I converted a drawing tablet reciever from type A to type C.

These are as-expected... but I did destroy 2 of them with a pad (one D- and one D+ on another) lifting. I thought I was being gentle and have not had this issue with other delicate electronics.

I like that they are just like factory ends. I don't like the fact that they aren't fast charging compatible. The soldering connection can be found online no problem. Don't have no instructions on how to put the housing together to keep the usb c plug in place so I had to use super glue definitely don't like to use that.

Ordered them with the expectation to repair multiple cables I had instead of buying new ones. However these don't work for my needs. They came fine. Just wrong specs for my devices.

Ce que j'ai reçu en une prise USB C avec 4 broches, je peux l'utiliser comme connections USB2 sur une prise USB C. C'est utile pour faire adaptateur USB 2 a USB C ou comme chargeur.

Die Einhausung des Steckers geht aus meiner Sicht nicht ohne Kleberfixierung des Innenlebens.

落下によりグニャっとなったアダプタの付け替え用途に購入しました。加工が必要でしたが要件は満たせましたので満足です。ついていたコネクタをばらして配線確認(V/G/CC)→R1(56kΩ)チップ抵抗を外す→外したランドとVの間をカット→V/G/CCの３本を半田付けといった手順です。ピンアサインは一応ネットで調べたものの心配だったのですが高速充電できました。他の方々のレビューのとおり強度が弱いです。補強のためシリコンを充填しました。５個入りなので壊れたらまた修理します。

とにかく使いづらい。１個目でNG。それを参考にして２個目を何とか。抵抗も取り外した方が良いのでは。取説で寸法関係を明記した方が良い。それと固定されないことをもう少し丁寧に。スペインの方？レビューにもありましたが誤解を招きやすいいので説明書で寸法と性能の事を明確にすべきでは。

Alles in Ordnung. Gerne wieder.