RJ45 Cat6 Connector Pass Through Cat6 Cat6a Ends Gold Plated 8P8C Ethernet Shield Modular Plugs for 23Awg/24AwgCable （50Packs）

works great with my klien tools passthrough crimper

Nothing

Reasonable price, good looking, and I got high success rate with these connectors. I opened the package for the first time and clamped both ends with these connectors of about 100 ft CAT6 cable to connect 2 routers. I got 1 Gbps speed right away. Highly recommend these connectors.

They work great. No issues.To make things a LITTLE easier on yourself. Keep scissors nearby. Get all the colors lined up properly and ready to feed into the end. Trim the ends so they're all the same length at that time and then insert into the end. This tends to make it easier to get the wires into the proper slots within the end.Other than that, super easy to use!

These are great - I don’t expect to run out but I will buy them again when I do! Works great with 23AWG shielded Cat6a. Note that you’ll have to ovalize the cable to get it to fit - I’m using the pinching motion on the handle side of some scissors to shape the wire. I recommend making a few practice connections first if this is your first time with Cat6a!

This things Work like a charm, and are well made. Have Already used more than a dozen with my Klien crimp....Very Nice

I confess that I was hasty in my research and somewhat misled by the way these connectors are marketed in the listing, though for the price and quantity of connectors, I rest content with my purchase. The listing mentions CAT6A and uses the word "shield", though these are NOT CAT6A STP (Shielded Twisted Pair) connectors. They lack the plastic insert, and they lack the clasp that gets wrapped around, or crimped, binding the drain wire with the cable's outer insulation. That said, they are great for UTP (Unshielded Twisted Pair) applications (which are the most ubiquitous) and they get high marks in my book for one very critical reason: the plastic that these are made from allows permits the latch, or hook, to fully bend back without snapping off. When I terminate network cable, I always use a boot in order to prevent snags and to prevent the latch from breaking off, but for users in a bind that may need to repair a cable in the field and do not have connector boots, these are a fantastic solution.

I bought these for my wired home network installation. I had never worked with network lines before, so I wanted to go with pass-thru cable ends to make it a little easier on myself. I searched for a while trying to find pass through ends that would fit with 23AWG CAT6 cable since that is what I was using. I'm happy to say that these worked for me without a problem.It was pretty easy to arrange the wires in the proper sequence and insert them into the connector. I found that it was easiest to get the wires lined up in order and hold them together as if they were a ribbon cable. I would trim the end off to get a clean leading edge on all the wires, and then I could insert them into the connector and they would naturally guide themselves into the proper channels for the pass-through. It was super easy.I would buy more of these again in a heartbeat. I used solid wire, and didn't have any issues with crimping or with connection issues on the cable tester. My network devices area all giving me 1 Gbps speeds when wired in with the cables I made, so everything seems to be performing as expected.

A little more work ... but a solid connector. I've sampled many connectors available here to only find that my 23AWG solid copper wires caused the pins to deflect in the connector cause the manufacturers used a lighter quality plastic (take a magnifying glass and examine your connectors).These connectors used a higher quality plastic and there is no deflection of the pins as they are inserted into the wires.

If you're doing this often, don't hesitate to buy the tool for passthrough. Otherwise, push hard on the cable, cut straight and pull back the cables a little.Good construction, What I appreciate the most is that the clip doesn't break easily compare to other brands that I've tried over the past years. Good buy!

Make sure your cable is not too thin as it will become a nightmare to use these connectors. Otherwise they are perfect for thicker cables.

Bought these because they were advertised as working with Cat6A cable. I've made many cat6 cables in my life and struggled for more time than I ought to have trying to fit all eight wires into these. Bought different connectors in the end.

Good