Edge Supply Birch 3/4” X 250' Roll of Plywood Edge Banding – Pre-glued Real Wood Veneer Edging – Flexible Veneer Edging – Easy Application Iron-on Edge Banding for Furniture Restoration – Made in USA

This is good quality edge banding. Pay close attention to the width measurement of the edge banding VS the width needed for your project. This edge banding is not ideal for 3/4” projects. If your an expert, you may be able to pull a 3/4” project off, but there is absolutely zero hang off (see photo). My project is 1/2” MDF I will be veneering in lays to for use as samples. This edge banding works perfect and the corners glue up seamlessly.Some reviews complain the glued together pieces are obvious or spaced too close together, making the edge banding difficult to work with, or unusable.1.) All edge banding this length will have many glued together pieces. There will never be a 250 foot tree cut and milled specifically to create edge banding.2.) Where this edge banding is glued together, it is a very wide zig zag, about 1” (see photo), and not obvious until you put the banding to your face and search for it. In the photo you can see the glue up on the raw edge banding. I had to get in some good lighting and tilt the banding at an angle to make the glue up obvious. After the edge banding has been glued & lightly sanded with a flat block (emphasis on LIGHTLY), using 400, 600, or 800 grit sand paper, its impossible to spot (see photo with my finger pointing to a glue spot that cannot be seen). The only issue you may have with the glue section being problematic is if you do not use something between your iron and the edge banding. If you apply banding with a lot of pressure, as with all banding, some glue may rise up to the surface. This can make the surface just sticky enough to catch film or dirt off of the iron...the dirt On the iron is the problem, not the edge banding. Recommend using wax paper between iron and banding for glue ups. When the wax paper has been used several times, replace it with a fresh piece.3.) I measured multiple areas to find the length between glue ups. My roll had glue ups, each one exactly as shown in the photo, around every 4 feet, pretty standard for this size roll.All in all, this is good quality edge banding at an exceptional value. The price of this edge banding will buy you 25’-50’ at the big box stores.RECOMMENDED

Great quality product and you get more by 2x for the price than any of the big box stores....

I purchased this banding to use on a furniture project. I used an inexpensive small travel iron to heat the glue, and it worked great. The banding stayed in place once the glue was activated, and we've had no lifting on the entire project since we completed it about 3-4 months ago. We finished it with a whitewash and a poly clear coat, neither of which affected the adhesion of the glue. There was close to a total of 150lf of banding on our project - all on plywood edges. Re-positioning during the project was no problem either; if we had a minor adjustment to make, we just ran the iron over the banding to heat the glue, and moved the banding to the correct position. Make sure to let it cool for several minutes before cutting or sanding away any excess material. Veneer was nice and clear, free of knots and other imperfections. Plenty of glue for good adhesion and it's applied uniformly so there are no spots without adhesive. The joints in the veneer are quite hard to see at first, and they sand down so well that they are virtually unnoticeable once finished.

We used this to trim edges of plywood for a murphy bed. The width makes it great if you're using 3/4" plywood, as there is very little overlap. It was super easy to trim with a sander instead of the traditional blade. Irons on easily, works as advertised. If you have something that isn't completely square or anything slightly rounded, this is not very effective. You can manipulate it with painters tape or something similar to get really close though which is nice. Great product if you're applying to a perfectly flat edge, otherwise I'd probably stick to older glue on veneer.

1.5 year ago I stained the maple edge banding and applied to vinyl flooring stair steps an in-ept (now unemployed) installer created. I reduced the width to about 3/8" used the tip of the iron and it has held beautifully. I saturated the product with pre-stain; no adverse effect on the glue.Last week I applied the birch to 3/4" birch veneered plywood for shelving, applied 3 light coats of polyurethane to match finish, then applied with iron. Looks pro.This is much easier to use than other pre-glued product. I couldn't be happier with the results.

The media could not be loaded. Everything came as advertised. The thickness was perfectly fine. The glue held up fantastic. I actually had to reheat a section of it and take it off of my project and then reheat it and apply it and it went back perfectly with no problems. The color is great and consistent I could not have asked for anything better. The product did have one seam in it which I consider acceptable in a 50 ft length. It was in the last two feet of the product which was not really an issue for me. Highly recommend.