KregPrecision Miter Gauge System

j'acheté cette jauge pour ma scie sur table évolution rage 5, satisfait de cet achat,après une modification de la barre alu guide qui a une épaisseur de 9,5mm à 7mm car la profondeur de la rainure de table n'a que 7mm,je pouvais le fraiser au boulot.la largeur de ce guide est de 18,6 et la largeur de la rainure de table est de 19,6,dans la largeur de ce guide y'a 5 taraudages M5,des vis M5 sans tête sont avec pour règler le jeu,autre bémol le mètre ruban adhésif est en inch,j'en ais acheté un métrique sur amazone

la verdad es que no he podido utilizar el sistema de precisión que adquirí, me ha faltado tiempo, sin embargo revise la pieza y tiene un acabado excelente y un ajuste de piezas también excelente no presenta holguras, no tengo la menor duda que en cuanto lo pueda utilizar funcionara a la perfección.

I use this on my R4512 and i'm super happy -- it just works. It's very easy to setup, calibrate and use.The build quality is spot on.

Recht teuer aber definitiv sehr gut, sehr präzise für holzarbeiten

WOW! What a nicely made item! You have to put it together. There are like four small bags of parts, some of which you may not need, depending on your saw table. There are a couple of extras of some of the plastic parts. The instructions lists exactly how many you need and you only use them on the single step involving them. You might have extras. They will not be used later on in the installation. You did not miss anything. ;-) The "fence stop" parts are shown in the instructions in a manner that allows you to clearly see how they are assembled, but the instructions never mention where they go; luckily, the box has some excellent information and photos. There is a small part on the "Swing Stop" (the "support button") that is a tiny bit too thick, preventing the Swing Stop arm from fully doing what it needs to do. I found that I had the Nylock nut too tight. Once I backed off on it so that it moved as per the instructions, the support button was only a very minor problem. Perhaps buying a small, brass or teflon washer sized to match the two brass ones in the kit (and maybe half as thick, hence my suggestion for teflon) would make this fit perfectly. The self-adhesive rule is METAL, so the instructions to use strong scissors or snips is something you should heed. I used scissors, large ones, and may need to sharpen them after doing this. You get a four foot section of this rule and you cut it at 1 and at 25 and it fits just about perfectly. The trough it runs in needs to be cleaned first with an alcohol swab (or whatever) to degrease it. The trough is exactly the correct depth, but there is a little bit of wiggle room from top to bottom, so peel off about six inches of backing at a time, press the rule against the far side and then press it flat a little at a time. Then your rule will be perfectly aligned. (This is totally not important. I am just OCD when it comes to being as precise as I can with stuff like this.) The four "glides" that are installed into the fence arm are TIGHT. I had to press hard to get them started and then tap them in with a tack hammer to get them fully seated. They look like they could easily fall out or move; they won't as the fit is snug. The little lens came in a small ziplock baggie. The other parts were in sealed bags. I saved the ziplock baggie for the unused parts. (The main unused parts - for me - were a T-guide for the track bar. My table has a 3/4" slot with straight sides. Some have a T-guide to lock the attachments in place. This kit comes with a T disc and screw for the track bar that I did not use. Since I may purchase a new table in the near future I decided to save these along with the extra nylon adjuster pins and glides; I might want them later. The brass lock pin was missing in my kit and I was sort of pissed off about that. Then I took the thin, plastic tray out of the box. It has fallen out of its little cubby during shipping. It is the only LOOSE part on this device. You need to make sure that however you store this that this pin does not disappear on you. It fits snugly, and if you sort of torque the two fence and guide together a bit and then lock the protractor down the pin stays in place well enough. Excellent product. I like Kreg stuff and will buy more. Easily as nice as the Incra, perhaps nicer. Recommended!