PedaltrainPT-PB1 Pedal-Booster - Single 3.5 X5.5 Inches

Needed to give my HX Effects some lift on my PT Classic Jr. I’m only using Velcro on the contact points versus screwing it down. Works perfect, but it definitely puts more pressure and bulge on the top of the soft case when zipped shut.

Just so you know, if you have the Novo series, on the first four rows, the booster is a little deeper than the two rows it rests on. Not a huge deal and still five stars, but thought I should mention it!

I have had a PedalTrain2 w/hard case for a few years, and two of my favorite pedals were always a little low on the back row. They are a TC Nova Delay and MAXON FL-9 Flanger, and while the TC just needed height, the FL-9 with the Ibanez type switch also needed to be leveled because it was tricky to push down on the actuator at the stock pedaltrain downward angle. These are not cheap pedals, and it was really a bummer that I would have to perform an annoying dance to activate them, and many times would inadvertently hit the knobs of other pedal.Well I just finished installing and testing the Large Pedal booster, and it fit those two pedals perfectly. I was concerned because the Nova delay is fairly wide, but no problem at all. The booster velcro'd in nicely, both pedals fit just fine, and immediately I could use them easier than if they were on the floor because of the added height and fact they are both now level (YES!!). It honestly feels like a new board because all my pedals are equally useable and I no longer have to worry about messing up other settings.And most importantly, my pedalboard still fits perfectly into the hardshell case.You will need to lengthen the connecting cables a bit because of the added distance, but the little bit of work is totally worth the return.All and all, the PedalBooster was well worth the money, and I only wish they had made it a few years back. Highly recommended if you have some pedals that need a little boost or leveling.

Na

Worked perfectly with my Pedaltrain Classic JR. Very easy to install. 4 stars for no printed material containing pilot hole drill bit size (I had to guess my way by using increasing bit sizes until the screws tapped). Otherwise an easy install, very solid and does what it should. Installation tips: 1. Take the pedals off your board before installing to make the process easier to manage. 2. Put painter's tape on the board rails and on the Voodoo Labs power supply. Mark the center points on each and line them up to center the power supply on the board. 3. Hold the power supply in place and mark your drill holes on the tape on the board rails with a pen or pencil so they're clearly marked before you drill. 4. Keep the screws holding the brackets to the power supply a little loose so you can "fine tune" placement once the brackets are installed....then make any final adjustments forward or backward and tighten them up.

If you are like me, and have a lot of pedals, there's a good chance you have multiple types of each one. When trying to put together a smaller pedlboard, for smaller gigs without disturbing my bigger board, I saw that this was about the perfect size for three standard pedals "as is".I ended up mounting rubber feet where the mounting holes that are supposed to secure the riser to you bigger board are. Small enough to fit in the front pocket of my bass gig bag for a very portable setup.I ended up using a combination of one bigger size pedal, the Tech 21 VT Bass, along with three other mini pedals, so able to easily fit four pedals in total in a 10.5" long "mini pedalboard".

Bought this to mount a voodoo labs mondo power supply to my pedaltrain pedalboard. Mounted up (gigitty) very well and it’s very sturdy so to answer two questions right off the bat“Does it work with a pedal train pedalboard?”-yes“Does it mount up to a voodoo labs mondo power supply?”-yes

Bought one of these last month to use as a small pedalboard on its own. I used the included velcro (which, if you let it cure the 24 hours it suggests, works very well) and just slapped some rubber feet on the bottom. Now, I have a small pedal board that fits three MXR-sized pedals (with patch cables) that I can take with me if I don't want or need my full-sized board. While there's no room for a power supply, I'm not disappointed at all. It's small, seems to be made of a sturdy type of metal (I'm guessing aluminum, like all the other Pedaltrains), comes with enough velcro, and most importantly, is only twenty bucks. If you want a small, inexpensive - but sturdy and attractive - pedalboard, just put some rubber feet on this, and I'm sure you'll be happy.

Overpriced pieces of metal. Does the job perfectly fine. I rather spend that bucks on it and play music, instead of wasting time on diy. Need to admit it's nicely finished and very sturdy. But construction/idea/fitting - blocks air flows on a side of Voodoo Lab unit - will that affect pawer supply? Time will show. Haven't noticed any overheating problems.Hopefully you can understand it from pics provided - side of the power unit has vents on both sides.Had to drill holes in pedaltrain, fits nicely, holds solid. Can't complain. Happy me ;)I recommend fitting power unit under pedalboards.

Shockingly over-priced, small bracket for attaching a Voodoo Labs power supply to a pedaltrain board. It probably cost about £0.20 to make at the most. Both Pedaltrain and Voodoo Labs are US products, and are themselves over-priced for what you get. But we're conditioned to pay more and more each year in an effort to escape the Chinese destruction of quality worldwide via cheap Asian imports I guess. What we really need is decent local manufacturers who won't rip us off....in other worlds a little of what was good in the old days

Does what it says on the tin, securely attaches a pedal power to a pedal train.I used it to fix a Mondo to a Classic 2.

Din't use as an add-on to larger pedaltrain, I used it to make a small indepenant board, (3 pedals and a wee tap for delay pedal), also attached some rubber feet/pads to increase height and to improve purchase to floor.

Perfect fit for Pedaltrain Novo 24 and Voodoo Labs Plus 2. Comes with self tapping screws.