BETCKEY - Compatible Shipping Labels Replacement for Brother DK-1247 (4.07" x 6.4"), Use with Brother QL Label Printers [10 Rolls + 2 Reusable Cartridges]

Only works if you drill your own sensor hole in the leg. See photos.Absolutely does not work for QL-1110NWB out of the box. I spent over 5 hours trying to figure out how to get this paper to work with the printer.I initially thought I was an idiot and spent 2 hours trying to update the firmware and messing around P editor.Then I cut the leg off my sample roll and tried to stack the two legs, but the lid would no longer close.Ended up having to drill my own hole and use the 4.07x6.4 in paper size setting to get the printer to work.The right edge cuts off slightly but it’s something I can live with and doesn’t affect the shipping label.Seller should not advertise that this works for QL-1110NWB

I recently purchased this as they are the cheaper alternative to buying official Brother labels. Right out the box, these do not work. When I installed them into my Brother QL-1110NWB, I wasn't able to print, getting a message telling me the labels weren't genuine Brother products (or something along those lines). How I was able to fix it was this. On my (Windows 10) machine, I sent to Start > Printers & Scanners. From there I selected my "Brother QL-1110NWB" printer then clicked "Manage". On the left hand side I clicked "Printer properties" and a new window pops up. At the bottom it will say "Paper available", under that there's a button that says "Preferences"... click that. A Brother window should open, ensure your Paper Size is set to 4" x 6" (as I purchased the 4x6 labels). Click Apply, then Apply again on your previous window, then click "Print Test Page". It should be good to go after that, printing across all your browsers and devices.

Ultimately, they work, BUT...1st issue, see the first photo (of the box), is not likely the vendor's problem. The first box received had a sticker for the correct product placed over a sticker for a different product (which what was actually in the box) and was not what I ordered. Amazon was very good about returning it and immediately shipping a replacement.2nd issue, see the second and third photos, the product description clearly reads "[10 Rolls/2000 Labels + 2 Refillable Cartridge Frame]". What I received is 10 COMPLETE rolls of 180 labels WITH frames (1800 labels) - and yes, I COMPLETELY UNROLLED & counted the labels.You can see, in the photos, the original roll of 180 BROTHER labels, compared to the Betckey roll (of 180 labels) is larger than the roll by this manufacturer. What isn't apparent in the photos is the feel of the product. While it is adequate for my usage, the replacement labels FEEL thinner than the Brother originals. That explains why the roll is visibly smaller.Overall, it's slightly disappointing that the product is not quite as advertised. However, they do work without needing any modifications or hassles regarding the frame that the picky QL-1100 wants. Additionally, they are a better value than the original Brother labels, so, I can live with it.

Let me start off by saying if you're hoping to just pop these in your machine and go, it's not going to happen. There is an extra hole on the official brother device, so you'd either have to drill one in, or do what I did which is removing the cardboard from the original brother holder, pulling it apart, and putting your new labels on the official brother holder.I followed a tutorial on YouTube (just search "Change brother ql1100 rolls" and it should come up. ), And basically when you run out of labels, you have to soak the plastic piece in water, get all the cardboard off and then pull it apart. Add the new labels, put it back together and put it in the printer.They seem to work perfectly once you're able to do the steps above.Update(9/20):Every 3 or so labels, it tends to skip a label. This means I have to try and manually feed a single label through my printer (which does not always work and takes forever). So I'm not sure I'd recommend these if you're high volume.Update (10/20):Every other label I'm getting an extra label being spit out. I tried to manually feed the extra label through with a little bit of the wax paper part left, so that would have some extra to go off of, but it only works some of the time. This means that a lot of labels are getting thrown away, which means a lot of wasted money.

These will not work in our machine. It keeps popping up that they are not the official product for the machine and to then buy them on Brother's website. How do you get these things to work?????!!!!

These labels are compatible with the BROTHER QL1110-NWB printer. HOWEVER, the rolls needed to be put on the original cartridge that came with the printer. The cartridge that these labels came with did not work with the printer. There are useful YouTube videos showing how to reuse the original brother cartridge that came with the printer. Once the labels are on the original cartridge, they print with no issues!

Labels overall are good quality. The print on them comes out great. they are a little thin but that doesn't bother me at all. They do work on my brother ql-11100 after you change settings. The big issues is that they don't stick that great. i probably used 300 hundred of them the first day and as my packages sat there for a bit all the corners started to turn up. I had to go threw and rub them all down again and hope they stayed on. That was on mostly boxes, they did seem to stick very well on plastic mailers.

It is perfect if the paper doesn't come out 1 extra blank page every prints.It is so much waste and I wasted so many blank labels.Tried to fix adjusting paper sizes and whatever I could do, but did not work.wasted money.

The price is amazing for such a big pack of labels. They are almost the same quality like the original Brother labels that l got when l bought the printer. Very happy with this purchase

No dislikes, very good value for money

Son perfectas, comodas, y muy bien pensadas, la verdad muy contenta con las etiquetas.

La qualité est au RDV, le prix est intéressant, mais je retire 1 étoile car il vous faudra récupérer le support d'origine pour que ça fonctionne (très simple, des tutos youtube l'explique très bien). Je recommanderai sans problème (et prochainement) cet article.