Truglo Tritium Handgun Sight High-Visible Front & Rear Night Sights with Daylight White Dots & Low-Light Tritium Glowing Green Dots, Compatible with 1911 Handguns

Perfect replacement sight for my Tisas 10mm commander. After installation I checked the sights for zero. Height was dead on !!!! Very bright tritium sights!

It was not a direct fit I had to make fit but it works great thanks

Doesn't fit the Taurus 1911 full size. Doesn't state if it's a true fit. Very vague...

I received a replacement set as the front sight on the order was not showing well in the dark. Faulty tritium insert? Anty how the sights are installed and the horizontal accuracy at 30feet shooting off a bean bag is bang on. The vertical however is about 8" low at that distance. the front sight is too tall if all 3 dots are inline. My original set as fitted so were within 2" vertically at that distance. The original front sight was a ramp which I painted white. Any body got any ideas? when the front sight is level with the top of the rear sight so higher than the rear sight dots then I am on target. If the rear sight was a bit taller it would all be good.

These are very nice night sights. They tritium vials are quite bright, just as bright as Meprolight or Trijicon sets. The white dots surrounding the vials are more than adequate for gaining a good sight picture in the day time too. These were easy to install, and only required minimal filing to fit the Novak cuts on my slide, as they should. I used a drop of blue Loc-tite under the base of the front blade, and on the screw for the rear sight, and they seem to be holding in place fine. I do not have a sight pusher, and wasn't going to buy one to put these on, so I tapped the front sight in place with a hammer and a brass drift punch. This worked fine, and despite my less than gentle approach the sight and tritium vial remained intact. One word of advice if you install these the unsophisticated way I did, DO NOT HIT THE BLADE OF THE SIGHT. Only allow your drift/bar/punch/whatever to contact the base of the front sight. If you hit the blade, you can bend it and break the tritium vial inside. This would relegate your front sight to daytime only duty.

Ok, some word of advice here. I put an exact set on a Kimber pro carry and couldn’t be happier with the results. My latest purchase is a SA range officer champion with novak cut. I wanted to replace the front fiber optic. Looked around and almost all options were $100 plus for rear sight alone. I ordered this set as an alternative knowing i could return to Amazon without hassle. The sight is labeled Novak cut, but it is not 100% compatable with Springfield Armory products. This is not tru glows problem. SA for some reason takes liberties with their sight cuts.. not even sure a genuine Novak brand sight would fit without some alteration. That being said the front sight was a perfect fit, The rear sight was about 95%. Slide cut was off angle at the rear and slightly too deep. I tightened the set screw and you can see some light under the sight. I thought of shimming but tried lock tight as another reviewer did. That works. You got to look really close to notice the fix. They look great and fit flush with the slide with no overhang.

I used the TRUGLO Tritium Handgun Glow-in-The-Dark Night Handgun Sights for 1911 Pistols, 1911-Cut .260 Front/450 Rear . The front and rear sights went on perfectly on a Springfield Armory 1911 45ACP Loaded Model . No fitting needed . Using the Wheeler Sight Pusher, it took me about 30 minutes to get the sights off the slide and installed the Truglos.These Truglos are much better than the Trijicons that came with the gun. and at half the price. The dots are bigger and brighter which make it much easier to see. Fpr the price, these Truglos cannot be beat.

I replace the original iron sites with these because they were just a little bit easier to see