Household Essentials Ironing Board Cabinet, In-Wall Recessed Ironing Board Cabinet with Storage Shelves, Unfinished Wood, Oak

It is fantastic, it exceeded our expectations!!! It is very sturdy. I love how it saves space and how clean it looks being in our wall. I highly recommend you getting it!!!

This works well, installs in a snap. I had it in the wall within 45 minutes of delivery! Plenty of room for the iron and the spray water bottle most of us use while ironing.The directions leave a bit to be desired (they mostly all do these days, so this may help. You'll need the following tools to install this ironing board cabinet:Stud finderSheetrock sawDrill and bit setPhillips screwdriver or power screwdriver2' levelTape measurePencilVacuum cleanerI strongly suggest that you choose the location carefully as you are going to recess this into a wall. Be sure there is no electrical wires or plumbing pipes in the wall cavity you are installing this into. Also, if your interior wall that you have selected has studs on 24" centers you'll need to frame the opening down to 14 1/2" in order to mount the cabinet.The door attachment to the recessed cabinet is a little tricky to do by yourself, you may want to have someone give you a hand holding the door in place while you screw it in. Be sure to drill the holes into the cabinet BEFORE you install it into the wall or you'll struggle to get the door to hang properly.My wife loves the ironing board out of the way and easy to access. In addition, right out of the box it looks great on the wall.

Bought this for our new house. The builder installed it during construction. It is just the right size and does just what I wanted it to do. Nice cabinet in excellent condition. We had an outlet installed below the cabinet for the iron. It has a metal inside corner to store the hot iron if necessary. Only problem is that the hole for the bolt that attaches the board to the swivel stand was bored from the wrong side. So they had to install the board wrong side up. (Otherwise, the bolt would protrude above the board and you wouldn't be able to skim the iron over the surface without running into the bolt.) The only downside is the edges of the board's bottom are angled rather than rounded like the top side, so it will probably wear out the cover more rapidly. But I don't use it for heavy duty ironing, just what I plan to wear that day, so not too worried.

I feel real bad for my wife whenever i see her iron her clothes on whatever surface other than on a real ironing board, and the fact that our tiny house has limited storage for stuffs like full-size board are the reasons why i chose to purchase this unit.I was able to get a returned one with price discounted. Its flawless with not even a minor scratch on it. I just wished for the manufacturer to be more clear on how to mount the hinges on the main frame, and much stronger hinges rather than the part-plastic ones that looks like they wont last due to the weight of the door and the clothes hanged on the corner hanger.A lower profile design also should had been available. I understand the 3 inches protrusion to accommodate the storage of the electric iron itself. Many folks would rather store the iron somewhere else and have a better looking unit on their nice wall.My wife is happy. No longer she hunches over the bed to iron her dress on it, or use the kitchen counter.I'm giving it a 4-star rating.I recommend to check the wall studs clearance before installing (or even considering of purchasing it).

Love this! The swivel feature is perfect and I use it all the time. It holds an iron inside, which is convenient! But I have an outlet very close, which is needed. The only thing I added was a child proof lock because if you open the door, the board could come down hard, so I highly recommend child proofing this! Great quality and just what I wanted! When installed, my laundry room was remodeled down to the studs, so we knew exactly how this would line up and had to make some adjustments.

This is a decent design and functions well enough (the MDF ironing "board" is a bit floppy and we may add a bit more padding under the cover). Given few decent alternatives it may be the best at this price point.That said, the craftsmanship and some of the materials choices seem more like 7th grade shop class than a professionally manufactured item. Too many shortcuts, where a few cents spent on better materials and attentive assembly could have made a better product for little or no additional cost:- The interior box is plywood with a paper thin face veneer. This means it tended to lift up one of the shelves and it is much too thin to take a clear finish or stain without a blotchy appearance. A better ply should be used.- The oak door is reasonably nice, but ours came with a large defect on the inside panel, a small defect on the outside panel, and wood not well matched in the frame (it took extra effort in staining to get all the frame pieces the same tone). Rather than sending out lousy doors and replacing them when customers complain, the manufacturer should get them right the first time. In our case, we'll live with the defects, since there seems to be no guarantee a new door will be any better.- The screws are very cheap -- three of the heads snapped off during installation. Better screws and hinges might add a few cents to the cost.- The metal heat shield is crudely attached, with staples through the aluminum and into the wood. The unit would be easier to stain or paint inside if this were attached with screws or, later, with brads -- I'd rather spend a minute attaching it than taking care to stain or paint around it.- While the door and surround are actual oak, there is an oak-like trim around the sides. This is actually MDF (dense particle board) with another paper thin veneer, in oak. The main problem with these side pieces was the amateurish construction -- one piece was 1/8" too long and the whole thing was fastened with gaps and discrepancies where it fit the face frame. The interior box was stapled to this from the inside. Given the thin veneer over MDF, attempting to sand things even is likely to end in disaster. There's really no good excuse for the sloppy assembly.- In addition, the trim from the face panel back to the wall is incomplete at the top and bottom -- presumably because most people won't see this unless they are tall (top trim) or bend down (bottom trim). However, it will trap dust at the pocket that's left at the top and it does show as missing from the sides if your wall isn't perfectly flat. How much more would a few square inches of oak faced MDF cost?One point I'd add for those with 6" studs is that the side trim pieces can be trimmed back about 1" to set the unit deeper in the wall (if you have 2x6 rather than 2x4 studs). At least 1" of side panel looks necessary to hold the face frame. You can also fill in your own missing top and bottom trim pieces. This is what we did, and having the whole unit an inch deeper in the wall looks better to us.Overall, the ironing board looks and works well enough when all is said and done. However, the manufacturer should be ashamed at the many shortcuts in quality and execution -- all of which could easily be avoided.