DNA MOTORING STEPB-ZTL-8106-BKPL Pair Factory Style Nerf Bar Side Step Running Boards Compatible with Jeep Wrangler JL Unlimited 4-Door 2018-2022, Black

For one of the running boards, the holes didn't match up. We had to drill a hole next to one of the holes. Also the screws that come with the boards are cheap and strip easily. I recommend buying more sturdy screws from a hardware store. Otherwise, it's been good and sturdy.

First off I'll start with the negatives: #1-The steps had small spots of rust on them in various locations. #2- Where is all of the hardware???? I had to go down to Lowe's and buy some washers because mine didn't come with the required amount. The package that contained the nuts and bolts was sealed up so I know that it was a manufacturer fault. #3- The bars were slightly warped so they didn't line up flush with the Jeep's factory mounting holes. I had to put one bolt in the front barely on, and then one on the back barely on, and then tighten them little by little to straighten it out. #4- The shipping was not fast at all and good luck with tracking it until a day or two before you get it.Positives: #1- The bars seem sturdy and seem to have decent welds on them. #2- The holes ligned up pretty good with the stock mounting areas. #3- They definitely look good and add functionality. #4- They kind of double as rock railing due to the angle of the mounts.Would I buy these again? Probably not.**Be prepared to buy your own hardware**Takes about an hour or so to do. Having someone help is even better.Tighten everything once all bolts and nuts are attached and aligned, it will save you some time. Good luck!

Easy to install. I like the sturdiness because they feel safe and the finish this nice too. They’re more like off-black, if that’s a thing, which makes it look like the fenders of jeeps. The only reason I would not fully go for these is the fact that all holes align except one of them. Meaning.... one hole does not have a screw on. It still feels safe to get on it and does not wiggle, move or anything, it’s perfectly fine, but aesthetically, looks different. There is absolutely no way to make it align, unless you open another hole on the metal of the car. Other than that, if you don’t care for that one hole, they’re great.

These fit great and look great but have the worst instructions in the world! I will tell u how to get them on without spending as sh*t load of time figuring it out. First of all, there are 6 brackets, 3 keyed to driver and 3 keyed to the passenger. One bracket on each side is smaller than the rest and that will go nearest to the rear tire. Hand-tight the brackets on the jeep first, don't tighten anything! Then hand tighten the bars on and u will be golden. Great product with terrible instructions but if u follow what I'm saying u will have them in within 30-60 minutes.

These were easy to install, look great on my 2020 Rubicon. My only complaint is that there are a few chips in the red paint around some of the rivets. I’m guessing that the paint will chip further at those locations as time goes on (they’re very tiny now and not too noticeable). I’ll update the review in the future if the paint does fail.

The quality and look of the Running board and mounting hardware is very nice, However the bolts that come with are too small and should have bigger bolts. We went and purchased more so no big deal. We just wanted a more secure fit. Also the labels were wrong but we figured out to just swap the right to the left side and vice versa.

The install was not as easy as it should have been. The steps were not level forcing me to use a jack to install center set of bolts. Bolt holes did not line up since running boards were not straight. Hardware provided was silver with running boards being flat black. The powder coating had bubbles in certain places that I could pop to expose metal. You get what you pay for on this one.

Easy to install. Took 30 minutes total. Material is a good quality and looks great especially for the cost. We don’t off road so chipping shouldn’t be an issue for us.

Installation paper pretty much useless. Had to figher out everthing on your own. Back bracket is the smaller one. Front and middle brackets are the same. Hand tie everthing on first then used socket wranch with 10mm and 13mm socket. Middle bracket is little off attaching to the car. if you put the washer on first it wont fit the screw in. One of the rod bolt on the right front bracket is busted even tho I hand tight everything. Shows in the picture. Too lazy to return it cus is a huge box don't want to ship it back. should be ok cus is not the driver's side. Spay some WD40 on bolts and nuts after installtion just incase they rust.

These running boards fit great on my Wrangler. I had no trouble with installation. As everyone has pointed out, the instructions are useless. Put the two smaller brackets on the back and hand tighten everything (no drill) and you should be fine. Would highly suggest adding rust proofing spray to the nuts and bolts as it's a sure fire rust target. Otherwise, nice looking and great value.

Product is exactly what was expected, but no installation instructions. Pretty simple to figure out.Two brackets are a little different and are for the back position.

One screw broke off without even power tool used, poor quality.The right side of steps is about half inch shorter than supposed to be, can't really fit correctly.

la boite est arrivée brisé et quand je les ouvert la pièce etais briser et poker