Tesseract Premium PLA + 1.75mm 3D Printing Filament | Dimensional Accuracy +/- 0.03mm | Compatible with Most FDM Printers | 1 KG 3D Printer Filament - PLA Skin (Quantity 1)

The filament is dusty and slightly undersized. I suffered three or four clogs before figuring out the best setup. A filament filter is required to prevent clogs. Oiling the filament seems to help. The color is a very dark purple as can be seen when held upto light. I had to print at 205°C to get good layer adhesion. Fevistick (only from Fevicol) works as a bed surface and holds onto the print well. A part cooling fan is also required. The filament will break if kept in a bent state for too long i.e. inside the printer feed tube.FYI the seller offered cashback for a positive review. I did not take the money. This review is my honest opinion.

-Strength Strength of this PLA is on the higher side. I have used this filament to make a stand for my ender 3v2 which dampen the vibration during operation. Till now it works smooth and fine.*Low infill will help you save material and increasing infill line multiplier it help you Increase strength which is very effective with this filament.Compliant mechanisms can be made even though it is brittle because it holds much load before fracture. It will fail no doubt to it "but how long does it take to fail" matters and I am satisfied with this.-Bed adhesion Company recommends to use heat bed @60degreeC and with that configuration it works well. Since PLA usually don't require heatbed I tried without heating the bed and printed but it seems to warp a bit for longer prints but if you want it to run so, use a glue stick which adds to bed adhesion. So it's better to stick with company's guidelines here.-Quality Filaments measures up to 1.73mm just like they have claimed to be 1.75mm and they have mentioned a tolerance of 0.02 so it is okay. Since the filament Dia is almost the same we can use it for tight fits and those require high accuracy like fits and joints, holes, etc. Calibration cube measured close to 20mm which is as expected.-Overall value I ordered this particular colour because I wanted a lighter colour which close to Stock ender 3v2 theme i.e blue so that I can print upgradable parts which I have attached a few among them.This colour is same as advertised by the company and it looks cool.Comparing it's price of around 1000 rupees it is worthy and definitely recommendable.These guys have a collection of PLAs of different colour&composition. I will try them too.Initially I was doubtful to purchase from Tesseract due to reviews like filaments breaking and spools went unusable etc, but if you are facing that issue directly contact the service centre through the number given in the filament package, they do offer great guidance and they would approve a replacement if it is found to be genuine.Preferred setting(Ender series of printers)Hotend temperature = 200degC (0.4mm)Heat bed @ 60degC*My paint jobs are terrible

This is not Good PLA. Has high thermal shrinkage unlike PLA.Please refrain from buying this filament.

Please dont buy this product. Soon after using this every time my printer clogs and the print goes wasted. only solution i could come up with, to reduce the chance of getting clogs is to use a dust filter with oil . Without the oil i couldn't even make through a 1 hour print. But using oil drastically reduced the part strength and give a shiny look.

Bought glass red filament, so far printed two items. Print quality is great and adhesion also good on normal glass bed.Nozzle temperature :208Bed temperature : 65Speed : 75mm/s

The quality has gone down drastically. Don't go by the rating. It's because of the old batch of filament they had. I have used them it was good and at a very competitive price but now they are selling garbage. 2 out of 3 are either not well packed or are brittle that u won't be able to complete the print.What I have realised in the past few months of ordering filament is that all the compqnies are nearly as bad and as good. Now the trick is to read the latest review and not the over all review. What these companies do is produce a good batch and sell it at competitive price. This helps them get a good review and this traps a novice in 3d printing who just orders the filament by seeing the over all review and the price. By then these companies have reduced the quality of the filament and are now selling garbage. And the newbies are stuck with bad once.So my learning is go by the latest review and not the company. I have seen tesseract from being a best seller to now some one else. And never never take a non vaccum sealed pack just return it. It's not worth it. 99% chance is that the filament is brittle.Now After ordering based on the latest review keep ur fingers crossed that the company has not just started selling bad once and u are the first one to get the bad batch filament. But for that u u have amazon return policy.

very happy with the quality and easy with which i can print with this material really in love with. printed 5 to10 small prints all come out perfect with endo 3 v2 printer default setting and cura 4.8.0 slicer. good dimensional accuracy and have not seen any sign of moisture so overall good product but it is on little bit price can go for it if available in 850rs to 900rs range

I ordered 4 spools.. Different colors. This one is Brass. Printed great. Took 34hours for this large Mandalorian.Will try other filaments.Tried on my CR10 V3 and Original Prusa MK1.Value for money.I dont know if they also have PETG!