Art3d 19.7"x19.7" (Pack Of 12) Wall Panel 3D Pyramid, White

Love these wall panels. Read for full installation tutorial (one of many methods)First off, the description says “32 sq feet”, which to most people not using the metric system, means 8x4, which is the standard size for most sheets of plywood. These panels, however, are 19.65625 x 19.65625...so they don’t cover a traditional 8x4 sheet of plywood.I didn’t want to ruin my drywall in case I didn’t love them, so I wanted to put a backer board over my drywall so that I could remove it/the tiles if need be. Using liquid nails or double sided tape on drywall is a recipe for disaster if you ever want to remove it.I purchased 3 sheets of 4x4 hardboard from Menards at $5.50 a piece. I didn’t want to make a mess with liquid nails so decided I was going to use double sided tape. I picked up 3 rolls of 150 feet Gorilla heavy duty for $10 a roll. So my total for the project including the 3D panels themselves was about $130.The box has 12 tiles and I could fit 6 length-wise on my wall with about 7 inches left over. So I decided to do 2 rows of 6 panels.1. I took 19.65625 x 6 and got 117 15/16 and 19.65625 x 2 to get 39 5/16. So I knew that was the size my backer board needed to be.2. I laid the sheets on the floor, measured, marked, and drew straight edge lines across at the marks.3. I cut the sheets with my circular saw. (They Cut very well if you cut with the grain)4. I brought the sheets inside, marked the edge on the wall where the first sheet would sit, and then I marked the stud lines above the sheets so that I knew where to screw in so that I hit the studs.5. I screwed the panels into the wall at the stud points. For the corners of the sheets that were not close to a stud, I hammered some nails so that the sheets would not come away from the wall in those areas.6. I framed the entire structure with double sided tape. I also added a line of tape through the direct center. This way the panels would have at least 2 contact points with the tape in all spots.**note - if you mess up and pull the tape from the hardboard, the tape will not stick again so you will need to use new tape.7. I carefully placed the 3D panels onto the wall and pressed down firmly to secure with the tape. Take your time, it’s tough to unstick the panels from the tape.8. I ran my finger slowly along all the edges to make sure all the panels had good contact with the tape.9. Enjoyed my new wall.Hope this helps. These panels are awesome. With a little planning and patience, they can make a nice feature wall.

Super easy to install. Looks great. Fantastic easy DIY update

Loved these for the accent wall in my basement. I added trim to all 4 sides of the wall to help frame it in and I think it turned out great. Easy to cut the panels with a good pair of scissors. I used a tube of clear gorilla glue with a caulk gun. It was nice that I could move them into place if I didn’t get them into the perfect spot immediately. But it was a little hard to hold them in place long enough for the glue to partially set. They tended to slide down with gravity. I wanted to start from the top because I wanted the cuts to be near the floor because that’s where seals/chairs will be but if you start at the bottom then work your way straight up, the panel underneath will prevent slippage. And use a paper towel to rub the edges against the wall and that wipes away access glue. But because the panels are PVC it’s easy to run the glue off after it dries. Using my hands to hold/push the panels in place, I got some glue on the panels but clean up was pretty easy. Also, I rotated each panel 90 degrees so the geometry looked more random then having an actual pattern to it like you see in most of the product images. (My ceiling is not finished, just sprayed black)

We love the look of these 3D panels. Our carpenter put them up with either caulk or epoxy. Not 100% sure about that, but the instructions will say. I added a mirror for more depth. We're very happy with the way it turned out. I'm not certain how many boxes the carpenter used. It'll depend on the size of the room. Worth the money.

Make a great accent wall to give your room some texture, depth, and warmth. Used a Dremel tool to cut panels to fit. Used construction adhesive to stick to walls. Sides of panels (edges of panels) are slightly lighter in color. If they don’t line up exactly, you might notice light lines in between. Used 1/4” OD green car pinstripe tape to cover seams in between panels. Overall looks good.

I recently added the 3D diamond wall panels to my boys’ room, and I have to say, they absolutely loved it! The transformation was incredible. Installing these panels was a breeze thanks to the gorilla glue construction adhesive. It held everything securely in place, ensuring a long-lasting installation. I was delighted to discover how easy it was to install the panels, saving me time and effort. To achieve a seamless finish, I used white caulk to fill any gaps between the panels, and the result was flawless. The walls now have a stunning, three-dimensional look that instantly elevates the room’s overall aesthetic. I couldn’t be happier with this purchase, and I highly recommend these 3D diamond wall panels for anyone looking to add a touch of innovation and style to their space.

The media could not be loaded. If you really want to give your room a unique upscale look I highly suggest these pannels. They cam in perfect condition make sure you measure your wall before ordering. Measure twice order once I got two of the 12 packs and had two left over. These are really amazing and when the light hits these it gives it a great look. Make sure you use liquid nails to put these up. The gorilla double sided tape is actually hard to use. Liquid nails makes it easier to stick. These definitely seem very durable and the size is great and materials seem solid.