POWERTECToggle Clamp, 300lbs Holding Capacity, 302F Quick Release Push/Pull Clamp for Woodworking Jigs and Fixtures, Pocket Hole Jigs, Welding, CNC (20304), Pack of 1

Used this clamp to make a pen press. Works great

Good strength so far to hold what I am using them for. I wish they came with a rubber tip but I got sone rubber stoppers and just drilled them out to fit over the head of the bolts. Seem to work fine. For twice the money I coukd get one with the rubber tip.

These are good and they work well enough, but the fit between the plunger and the sleeve is looser than on the same type of clamps I bought from Xpaowa:https://www.amazon.com/XRPAOWA-Toggle-Release-Holding-Capacity/dp/B07214XRR1The smoothness also wasn't quite as good. There seemed to be less lubrication, and it was more sticky. As a result the plunger is a little more wobbley, and needs a little more force when extending and retracting. It still works, it just doesn't feel as nice.I figured it was all the same part made in the same factory, but I guess there are subtle differences. Another thing to note is that these have a 5/16-18 thread, rather than the 8mm thread on the Xrpaoa model.That all said it still worked for my application, and it still holds well enough.

It’s what I expected from what I sawThis will work the way I wanted it to

works good for me

Exactly what I wanted

These clamps work great. They hold great pressure if installed correctly

Overall, a nice design. there is one serious flaw, however: The little "pusher arm" is much higher off the work surface than it appers in the picture. Unless your work piece is at least 1" or more, the pusher arm will miss it altogether or tend to push it off dead center.

Well made and works as it should

I received the toggle clamps yesterday and after unpackaging them, one worked fine, but the second one was defective. It doesn't work in the vertical position, which is the way I need to use it. The handle is too loose and won't stay clamped because gravity pulls it down. The clamp that works, the handle has a detente in the clamped position so it won't release in the vertical position. I would have preferred to contact the seller directly rather than leaving a bad review as I would still be interested in the product if the seller replaces them for two good ones. But unfortunately, I couldn't find anywhere a link where I can contact the seller, so I decided to put a review instead. I will be returning the product and asking for a replacement.

Llego justo a tiempo, y en perfectas condiciones

nothing to dislike

Buen producto. Está fabricado completamente en acero, no tiene partes mecánicas de plástico ni otros materiales endebles. La aleación és perfecta en cuanto si fuerzas el aparato tiene la flexibilidad justa para no romperse y volver a su sitio. El émbolo está bien centrado y realiza un movimiento de vaivén perfectamente horizontal.La base mide 91x5mm, llegando a 140 de longitud con el émbolo totalmente estirado, éste se encuentra a unos 24mm del suelo. La planca mide unos 90mm que inrementan tanto longitud como altura máxima. La rosca no és métrica, en la descripción te dice que se asemeja a una M8 con paso de 1.25, pero no és así. Yo tuve que ir a comprar mi varilla roscada en una tienda especializada de mecánica para conseguir mi objetivo, pero se consigue.Lleva cuatro agujeros para fijarlo, que són suficientes, y la empuñadura de plástico és muy ergonómica y se agradece al tacto, aunque sometida a presión cede. El aparato soporta unos 130kg de tensión, en el punto de apriete, que és cuando la palanca está hacia delante, empujando el émbolo. Hacia el otro lado cede con mayor facilidad y la palanca no tiene una sujeción firme.En mi caso la usé para fijar una guia de corte de mi sierra de mesa casera, con lo que tiene un aplicación perfecta. Muy contento con el resultado y me apunto el fabricante para próximas compras de otros fijadores.