3D Printer Enclosure for Bambu Lab A1 Mini, Clear Acrylic Bambu A1 Mini Printer Dust Cover with LED Light,Dustproof Tent Constant Temperature Protective Cover Box(470×470×470mm)

Solid build. I read a lot of reviews complaining about the acrylic plates rattling, but I can barely hear it. There are shims on MakerWorld (just search for Yoopai and you’ll find everything).The A1 Mini is not designed for ABS, so keep that in mind if that’s why you’re buying this. The enclosure and the printer will both require modifications.The LED is plenty bright.Assembly wasn’t the quickest thing, but it wasn’t particularly difficult. Just make sure you pay attention to orientation; I had to start over halfway through because I put one of the sides together backward (entirely my fault).It fits the print nicely. I would not recommend using this enclosure for anything larger than the A1 Mini tho. I tried to put my Ender 3 V2 in it and it was slightly too tall.Overall a nice product for the price.

Assembly was not as bad as expected. Dont try to pull the ptfe tubes from your hub as it can break the hub. Use your existing tubes or order a new hub. (Specifically for bambulab A1 mini)Love it other than a little rattle that can be remedied.

The directions for putting the enclosure together were worthless. The parts have to be assembled in a specific orderor they won't go together. The reason is the panels cut notches have to be installed in the beam members in an exact order. I had problems with the door hinges.I had one door where the hinge pin was screwed on and broke into four pieces. I could only find three of them. There was no way I could fix the door. Then I had the second door crack at the hinge pin. I was able to superglue it to hold the door in place. I reached out to the seller who responded they needed a picture. I am 78 years old and can't give them a picture. I can't believe they would think I just wanted an extra door.The enclosure is put together except for the broken door. The sides are very loose in the framing members. The enclosure will not stop the noise but it will amplify it. I will need to add shine all around to tighten the sides to the framing members.The seller has declined to help me with the broken door. They are not going to send me a new door as requested.I would not recommend you to purchase it! You can get a soft shell enclosure that would dampen the noise and keep the heat in the enclosure. This alternative is much cheaper.After reading all the reviews I found that many of the reviews complained about how poorly they were written. I found several individuals that had the doors break at the hinge point. All the panels set loose in the framing members require shims to be installed. The seller did not include any shims. The seller did not respond to the poor reviews and what the buyers could do about it.I would like Amazon to remove this seller from their website. The seller clearly knows the product is poorly designed. Also, the seller has no intention to address buyers' issues with part replacement.

This is a good enclosure kit for a very reasonable price! ($99.99 with a $10 Coupon at the time of review). The aluminum extrusions are very sturdy and fun to assemble. I appreciate the extra hardware is included, as I tend to lose some to the floor!My only suggestion for improvements is to add some shims to keep the acrylic panels from rattling as the 3d printer moves and to either reinforce the cable grommet cutout or make the grommet a more flexible durometer so it's easier to install without breaking the cutout.

I hated ever minute of putting this together. Instructions are terrible. Took me several hours and a lot of angry words. Looks nice now that it’s together, but I wouldn’t buy it again.

This is a good enclosure that doesn't require any 3d printing to use. Considering the plexi &al extrusion, it's good kit. A little rattle, but easily fixed. Also, put a solid board on the bottom to reinforce.

I spent probably 12 hours over 4 days assembling this enclosure. The instructions consist of a sheet of paper and the video in the listing. It’s not enough. So 4 stars not 5.Learn from my biggest mistake: mark the pieces that are the beams with their attached connecting pieces! This would’ve saved probably 3 hours of re-assembly.Print files for the AMS attachment and the waste bin printed flawlessly.The printer hits the waste bin if you don’t remove the single spool holder from the back of the printer and move it over. It’s still attached in the photo.Glad to have our new printer enclosed and protected.

I absolutely ❤️ this enclosure exactly what I was looking for a clear enclosure that I can see clearly from front view and sides. Helps keep sound down also helps to keep your printer collecting dust. Great lighting. I would buy this again as well as recommend it to a friend.Update… still enjoying my enclosure I’ve since added a magnetic strip to the inside of the door then I put a another strip on the outside center of door to keep the door sealed and flush works great. Did another update changed the light with a led color changing light pics added