ALITOVE 24V 25A 600W Power Supply Adapter SMPS Switch Mode Power Supply LED Driver 110V 220V AC to DC 24 Volt 25 Amp 20A Converter Transformer for LED Light CCTV Camera Radio Speaker Amplifier Motor

I bought two of these 24V units to power a decent sized COB LED strip installation in my kitchen. I also bought three 5V units to power a BUNCH of RGBIC LED strips, two hooked up to a switched circuit, and one always on. The 24V units are on a separate switch.So far all of the power supplies in the installation work great, only complaint is that the fans get noisy on the 24V units after the lights have been on for about five minutes.My complaint about the fans really has to do with one of the power supplies which turns its fan on-off-on-off to regulate the temperature of the power supply depending on how heavy the electric load is, while the second one has a smooth speed control on its fan and ramps the speed up or down to keep its temperature controlled. I much prefer the self-adjusted fan that runs at much lower RPMs than the power supply that turns its fan on and off, because that one turns the fan on full-speed and makes much more noise, and brings attention to the fan noise by constantly turning it on and off. I’m planning to move both of the 24V supplies to a location away from the kitchen so that the fans can’t be heard at all.The voltage measures clean on both, and the output is adjustable so you can dial in exactly the voltage you need for the application you are connecting it to. The voltage is well regulated as well.Great little power supplies at an affordable price. Highly recommended.

Had plenty of power and even short circuit protected. I accidentally tested it.

I used it as part or a inverter i built to get 115 volts AC from 24 volt battery.

First thing to mention, this power supply does its job. For the price this thing is well worth it, but that's not to say it's perfect. The packaging used for shipping could definitely use an upgrade. Mine came with the metal shroud bent, it was just inside its box with no protective foam. Second issue I have is there is a bit of coil whine while under load, it's not loud but is there.I purchased the 15 amp to use as a diy boost pack for my fanatec csl dd. It works without any major issue and shows up as the 8nm on the driver software. If you're thinking about doing this yourself I would say go for it and save yourself some money.

At the time of writing this review, I have owned the power supply for about a week. This unit is working great for me so far. I used them for powering my COB LED lights using a DigUno board. I previously bought a different brand which had a fan and was extremely loud. I bought this one because it was designed without having a fan. The heat dissipation on this unit seems to do very well. I stuck a thermometer over the coil and it registered about 125 degrees. Other areas of the board were around 85-90 degrees. I placed the unit on top of some metal risers to allow for airflow under the unit as well. Overall, I like the unit so far. Hopefully it will last a long time.

I purchased the 24v supply in October 10/24. I didn't get a chance to use it until last week 12/24. I connected 2-12v 4" fans and 50' of WLED 5050 strip lights to my sons computer desk. Got everything all buckled down and nice. Looks nice, got some gentle airflow, everyone is happy.Maybe 30 to 40 min later "KAA-PLUUU-FIEEEE". Capisitor go boom.No support.Temporary single use power supply.Sad, that things are such low quality these days. Perhaps it's time to start making my own power supplies again.Youtube it people. You can do it too. Far better for less $ and VERY little effort and skill needed.Sorry, but I demand better for my $.

I used this as an "external battery charger" for a fire alarm panel in a 30,000 sq ft building with a failed onboard charger. Saved the owner several thousand dollars if they would've had to replace the panel.You will need to have basic AC/DC knowledge. I ultimately hard wired this power supply, but to test it I cut the end off of a computer power cord. Depending if the cord uses US or international color coding on the internal wires, you will either see black, white, and green (as I did in this case) or you will see brown, blue, and green w/ yellow stripe.L (live) will be BLACK (or BROWN)N (neutral) will be WHITE (or BLUE)G (ground or earth) will be GREEN (or GREEN with YELLOW stripe)For the DC side just observe polarity (which you probably already know if you're buying this).Voltage is adjustable from 19.9 to 30.4 volts with the orange potentiometer (you can use a #1 phillips screwdriver). It is to the right of the terminals. Out of the box it was at a perfect 24.0 volts. I recommend this power supply.

This power supply arrived quickly and in good condition. It will be used to power stepper motors in a CNC machine.