Solutek Buttons Guitar Pedal Footswitch Toppers Caps - Aluminium w/Lining & 3 Screws – Offer Accuracy, Comfort,Protection,Identification,Decoration (Multi-color V1 for 3/8" 10mm Switch)

These install fairly easy and have 3 set screws to hold them in place. Only 2 set screws would offer less stability, so I'm glad there are 3. The size works well and adds some much needed height to my back row of pedals on my board. They are now easier to reach. A previous "button topper" product would only fit certain size foot switches, but these accommodate all my pedals.

EDIT: I Bought another set to complete my FM9 board; still fantastic, picture included :)____I bought the 6 piece set of black (3/8"/10mm) for my Fractal FM9. These came in a small plastic snap case (I am now using as a travel pick case) and with extra screws and two wrenches. I upgraded from an FM3 to the FM9 and have 3 other buttons from the expensive brand that cost $7 each that I was going to use on the top 3 buttons but I have now also ordered a second set of 6; I wish I had just bought a full set of 12 to begin with, or the multi colored set. I am going to put three on the top row of the FM9 to flesh it out and make it uniform and put the extra three I have left over on my other pedals.In my opinion these buttons are better than their very expensive competitors; the rubber insert prevents damage to the foot-switch and allows for even installation of all three screws. These fit snug right onto the switch with gentle pressure, and with the set screws in they will not come off. I had issues with the other brand coming off unless the screws were set very tight and potentially damaging/indenting the foot-switch. I believe the full contact of the rubber insert allows for more friction so it not only protects but grips the foot-switch more.Great quality, amazing value!

While for some pedal switches you may have to open the pedal and raise or lower the switch to make these knobs work correctly with the pedal, I must say that over all I like them. My only criticism is that they might be a little cheaper, but I am buying them again.

Quality is as good as I had hoped.

A good alternative to barefoot toppers. Cheaper and do the same job

I had to buy these because the Zoom MS pedals have a larger stomp switch than standard. (Large enough that the hard plastic buttons won’t fit without damage). A note for installing these: back the set screws out far enough that they don’t catch the rubber insert when you are pushing them on. The rubber will catch and get damaged or will make the caps not fit properly. For oversized switches, remove the rubber insert and place it on the button, then push the aluminum cap onto the rubber and tighten the screws. These work and look great if they are installed correctly.

These are hardly universally compatible right out of the bag, as some pedal switches will have clearance issues and make the pedal engage inconsistently or not at all. But I was able to reliably get around this with some felt padding I had lying around and a standard hole puncher.Simply punch a whole into the felt and place the cut piece into the inside of the topper, then screw it onto the switch like normal. If you don't have felt, you could even use several layers of cardstock or even regular printer paper. It's been a few weeks and the footswitches work 100% reliably and their tactile sensations are still intact.Also it's definitely worth noting that it is VERY easy to strip these screws. So be very careful and take your time.I would still recommend these given that the compatibility issue was a somewhat easy fix, they feel great in terms of their size, and the alternatives are over twice the price and/or ship with ugly branding.

Hey, these switch toppers really do work! I was not expecting much and figured they might be shoddy but I was surprised. I like playing in my bare or sock-covered feet and it used to hurt a bit. Not now! I picked the silver color for low light levels but there are lots of other colors. They perfectly fit all my pedals except one, which I didn't expect to because of the switch's slightly larger diameter. I "Gooped" the topper to the existing switch and it looks like factory and works like a charm. There are six to a package and I bought two packs to do twelve pedals. Seems pricey until you can see your pedals in low light and your feet hurt less.

Están muy bonitos, tienen hule por dentro y 3 tornillos para asegurarlos, mucho mejores que los de plástico que venden por ahí.

I had no idea something like this existed; great for giving you more control over your foot switches. These are particularly useful if you're practicing in your socked feet! It takes a while to screw in each of the three set screws with the included allen key, but combined with the rubber socket, it makes for a very secure attachment. These come in sets of different colours, or you can get them all in brushed steel; I find the colour coding useful.

Decent quality solid metal housing, with a rubber bushing, and 3 adjustment screws. Will fit fairly securely on the majority of switches. Depending on shape of button, tightness of screws, and both direction and amount of force, attachment may not stay level, could start to tilt over time, and require regular adjustment.

Great product but one cap didn't have any grub screws.