Tempered Glass Screen Protector for Panasonic Lumix DC-G9 G8 G7 G7 Mark II/DMC-GX7 Mark II GX7 III / GX9 GX8 LX10 LX9 FZ300 FZH1 / Ricoh GR III (2 Pack)

It was way easier to install than the plastic film screen protectors. It also fit my camera perfectly. However, it's a good thing there were two in the package because the first one was cracked out of the package. No big deal for me since I only needed one.

Fits very well on the fz300, was easy to install.

It is and exact fit for the Panasonic G9 camera. You have to be very accurate when installing as it covers the whole glass. All the way to the plastic frame around the screen. Even a millimeter off in one direction and it will not sit flat. That being said, once on it stick well to the screen with no bubbles. The glass is very smooth to the touch. The only downside is there is no anti-glare coating so it reflects in bright Sun. This is probably the best protector for the G9 and I would buy again if needed.

No fault to the seller, but just a note that the protector does not seem to lay completely flat on a brand new LUMIX FZ300, the corner of it is a little wonky 🙁.

09/26/2018So far the product seems good. Installation instructions were basic, could've use a little more words, but it was straightforward. They gave two sets of sticker guides and dust stickers plus you get another shield. So it was worth the price vs pvc films.Here's an installation tip. Make sure you are in a well lit area, so you can see any lint or dust on the screen.Hopefully the glass is durable and will last. I'll update the review if needed. I've attached some pics.

I have used many glass screen protectors for my iPhone, iPads and DSLRs (But, Never this brand) and almost all have proved to be easy to apply, stable for adhesion and it was pretty hard to tell that my gear had a screen protector on it at all.The Macolink out of the box had an odd layer of fine dust on the outside surface......enough to write in it with your finger. After carefully cleaning that surface and preparing my Pany G9 read LCD for application, this screen protector fit perfectly, but, one corner refused to stay flat and kept lifting off. (The G9 screen had been very carefully cleaned and I never touchd the adhesive side of the glass during application!).My Pany display was perfectly flat, but, when I tried rotating the Macolink screen 180 degrees (the adhesive is the weakest I've ever seen as it seemed too easy to lift it off and reposition it)... the warped corner was now rotated 180 degrees. It WAS indeed the screen protector that was warped on that area.Maybe I got a defective one, but, it just seemed this was old stock that was hanging around in a warehouse for a long while. The dust on the outer surface upon opening the sealed box should not have been there!In fact the included "wet" wipe pad was bone dry when I opened it (I thus used optical camera lens wipes instead that I have here).Returned to amazon for refund.Upon finding the Expert Shield brand now available at Amazon for my G9 and this same brand is in use on two of my cameras and my iPhone, ..I immediately ordered it and will review it once received and applied to my G9.

Recently bought a Panasonic DMC-FZ300 and the first things I got for it were a B + W 52mm clear haze filter and this screen protector. Screen protector went on fairly easy. Make sure your screen is perfectly clean and that the side of the protector that goes on screen is clean and smudge free also. Line one side up first then lay it down. Then work any air bubbles from center to outer edges.My protector fit perfectly with no alignment problems (to big etc) and rotating screen closes all the way like it should.Definitely recommend it for this camera.

I bought this for my Panasonic Lumix FZ300. The protector fits well and is easy to install. However the screen on my camera swivels and can close screen in to protect the screen. After installing this protector, my screen will not close and latch as it was designed to do, Disappointing!