Electrical Junction Box, Outdoor Water Resistant Nema Enclosure, Ventilated ABS Plastic WiFi Project Box with Internal Mounting Panel & Hinged Cover 9.2" Lx 7" Wx 4.6" H

Well-made and snaps closed tightly so I'm confident about shielding sensitive electronics from rainy weather etc. Mounting components on the inside back wall grid is easy with some small threaded bolts or screws rather than resting them inside where they could contact any pooling condensation (I live in a humid climate so that's a small concern). There's a strap-based vs a drywall or wood screw-based mounting system for the box itself which is helpful if you're not completely sure where your project will be ultimately located. Would buy again

Great box works well for a raspberry pi irrigation system 🤠 I put some plastic elbows in place of the vents to keep it water proof...

This box worked fine for part of my christmas electrical components. Some people may complain they are a little on the lightweight side, but that is what I like about it. Since it is only temporary, being light means it is easy to pack up and put away. The reason I only give 4 stars is, unlike every other box I have purchased this box comes with no internal mounting board.

This box closes securely and solidly. There won't be any water getting into this box. You can see in the image that it has plenty of room for my solar direct to hot water setup. From left to right there is a ground busbar, surge protection, breaker, fuse protection and a master shutoff. This is located outside near the solar panels which are on top of my chicken run.

This is a hinged box that is incredibly well sealed. I actually had to struggle to open it. In my 3rd photo the seal that is located between the closed cover and the box is shown. I really appreciate that this box does not come with pre-drilled holes and provides me with two 1/2" cable glands, that I can drill and place where I need to bring a cable into the box. It also has the ability to be drilled for the purpose of wall mounting if necessary. While not as thick as Carlon® PVC boxes, this is not as expensive at this size. I now look forward to putting the lights up this year.

This is a great project box, once you get into it. It was sealed shut!!! Must have traveled over the mountains, it had a suction pressure holding the lid closed, that waterproof gasket does a great job of holding air out as well. I finally got it open with a whooshing sound of air getting into the box. The box has brass screw inserts so you can mount a (purchased separately) mounting backer. It did include 2 waterproof cable glands, but they are for some thick cable. This is a high-quality box that matches the measurements in the product description.

It came with two cable glands as well although I didn't use them. Keep in mind that there are no openings of any kind with this box you will have to drill and waterproof anything you want to enter and exit the box. Also, not surprisingly, there are no regulatory marketing of any kind. I used it to house a power supply I made.

This waterproof junction box is a good enclosure for light duty DIY projects. It is well sealed, that's for sure. I had to pry a corner of the door up to open it as it had created a vacuum inside. Once I got an edge up you could hear it pulling air in to equalize pressure, then the lid opened easily.The fit and finish is good, and the hinge and latch pins look to be made of stainless steel. I really like the flip up door catches for easy access. There is a small lock hasp, so you could padlock it if needed. It comes with two plastic cable glands.There are a few issues to mention. It would be better if a back panel was supplied with it. Not a deal breaker, but it would nice to not have to make a plate to fit. What really surprises me is that though the blind holes for the feet are cast into the back of the enclosure, there weren't any feet included. If you want to mount it, you'll have to drill and run screws through the back, which means it's not waterproof anymore.Overall it's a good, light weight, light duty, somewhat weatherproof enclosure for DIY projects. If a mounting foot kit and a back panel were included it would be that much better.