EVA Foam Teak Floor Decking Sheet (94.5''x36'') Non-Skid-Self-Adhesive Flooring Synthetic Deck Marine Yacht RV Boat Flooring Mats(94.5''x36'')

I bought three rolls of this product, which makes the old boat look completely new and perfect! We first clean the surface of the boat and then wipe it with denatured alcohol. Then, the surface size of the boat must be determined to ensure that the Teak Floor Decking Sheet fits perfectly on the surface. Since it is easy to fall and stick to the ground during installation, so here need to make sure to place the product on a flat place, and then peel it in half to stick it on the surface. Very easy and my wife help me do all the job.This is definitely a job, but if you can do it patiently, it can be done easily! The decoration renew my old boat, looks great. I believe it is worth lasting for several seasons. Highly recommended, great value for money!

We replaced the snap in carpet with 3 pieces of the foam. We put a gorilla black tape between joints just in case it decided to shrink you wouldn't see the white fiberglass deck underneath. It looks great so far but we haven't had the boat out yet to see how it wears with 3 young kids and a giant Newfoundland dog on the boat. So far we are very pleased! I would HIGHLY recommend buying all the pieces you need in 1 order. We ended up buying a 4th piece at a separate time for the back swim deck and it was ever so slightly darker. It's fine for where we put it, but would have looked horrible right next to the ones inside the boat. We sanded the edges to give it a slight angle on edges we cut with a razor.

The media could not be loaded.  UPDATE after 15 months ...All areas with flooring installed out of regular sunlight are doing extremely well. I created my own borders and they remain anchored. Areas in direct sunlight need to be aggressively glued down and do tend to fade & harden.A few recommendations ...1) Make sure the rolls are flattened, preferably in sunlight, for easiest install.2) When installing borders, paint the area where the seams meet with marine black paint. This is because the seams separate slightly so you want to hide that seam.3) Install the material all in the same direction. This can be identified by the cut width of the stripes on either side.4) Don't be afraid to use too much adhesive. The more the better.ORIGINAL ... The material installs easily after some experience. It's best to use templates in smaller areas. Borders are not difficult and can be bent around mild corners better than I thought they would. My biggest concern is that the color of the material is slightly different between rolls so the seams can be seen a little. I'm hoping with time and exposure this will become a non-issue.

Could be my floor but some areas came unglued.

Product works well in the area put it in, even with the sunlight on it for months, the adhesion worked well also.

It looked great at first but it shrinks and expands causing it to lift. I installed it about 6 months ago. I do live in south Florida so it has been exposed to rain heat and humidity but I mostly keep it covered. Not one piece of it is still completely adhered to the fiberglass surface which was clean and smooth when I installed. The pieces shift as they expand and contract and it looks terrible now. About 2 months ago I noticed that the dye was leaking so now it stains shoes, feet, clothing, and anything else that touches it. Complete waste of my time and money. Don't know how anyone could have a good experience unless they write their review the day they install it.

As you can see in the pictures, it looks pretty good. In couple of weeks i will cover the entire floor. I wish i had more experience in cutting and installing, but i am getting better with each piece that goes on the floor. Material looks and feels very expensive. Excellent glue ( i added one layer of 3m spray glue)! Will buy 4 more rolls to finish the entire boat. 2003 Bayliner 265.Thanks to the seller!

The width of the "wood" pieces on the left edge vs right edge are not identical. You must be very careful when you are adding pieces together to see if they perfectly align or not.Dragged tool box across and the surface is damaged. The surface shows a clear mark of the dragging.Of the 7 panels I ordered, one panel was a much lighter color. Good thing I needed only 6 panels.