Clarke Double Headed Metal Nibbler DHC-2

Purchased this to cut a hole in the roof of my Renault Trafic for a skylight.Connects up to the drill perfectly, easy to manage direction etc, you will need a 12mm + drill bit if youre cutting an internal hole and for corners.Cuts quickly and without effort, easy to control.Remember to cover everything below you and use eye protection, the little chips go everywhere!

Bought this for cutting box profile sheets. I couldn’t fault the performance of the tool powered by a Milwaukee cordless drill, it leaves a tidy job. It has done a lot of good work. It can be a bit tricky to work when cutting across the profiles, still does the job at a fraction of the price of a cordless nibbler.10 out of 10 from me

Does what it is supposed to do. Easy to use

Haven't used it as yet but looks like it will do the job.

Great cuts so well once you get used to it . You must clamp your sheet well and if you want to cut a straight line use a clamped straight edge to push against.

I needed to cut the bottom out of my Laser engraver to fit a rotary attachment. Although I could have completed this with a hacksaw, the mess and vibrations could have caused issues. Bought this nibbler to do the job, and it cut through so easily. Love it.

Not what i expected.I feel that unless you no what you are doing this tool can be dangerous.The metal that is being cut needs to be very firmly clamped to a fixed work bench as you get a lot of vibration.Just disapointed.Have returned the item.

Bought this to cut out windows on my camper conversion. Went through a VDub door like cheese. A friend bought a “more expensive” model elsewhere and rang me to borrow mine after his had eaten all the nibbler bits supplied. So my “cheaper” model managed my windows and finished off the other van on the first cutter (there is one each end and a spare in the kit, so 4 really).If you plan to do the same try it out on any sheet metal or get used to it on the inside of the panel to be cut. Once you get used to the angle it cuts at then each whole window will take about 5 mins to cut.

Correct

Aufgrund positiver Rezension dieses Tool gekauft. Es wird in einer hochwertigen Blechbox geliefert, in der das ganze Zubehör Platz findet. Der erste Testeinsatz an einem 2mm Alublech, mit einem Akku-Bohrschrauber: Der Schneidevorgang hervorragend, leise und schnell. Man muss aber aufpassen, damit das Gerät an der Schneidevorrichtung nicht überhitzt. Man merkt es dann an Schwergängigkeit. Hier hilft dann etwas Bohröl - und dann geht's gleich weiter, super. Bisher nur ca. 2m Alublech 0,7mm, 1m Trapezblech geschnitten, kein Verschleiß festgestellt. Das Handhaben des Werkzeugs ist super, das Werkstück sollte aber festgespannt werden. Für gerade Schnitte an einer Leiste entlangführen. Die Schneidevorrichtung lässt sich um 360° drehen, allerdings passt kein metrischer Schlüssel zu der Mutter.Verglichen zu einem Blechnibbler elektrisch( www.amazon.de/gp/product/B07G2GT5FD/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1), ist der Clark-Nibbler wesentlich leiser, wendiger und kann dickerer Bleche schneiden. Der einzige Nachteil, dass zwei Hände für das Schneiden benötigt werden.

Attrezzatura molto utile nel taglio di lamiera e fogli di materiale plastico. Robusto nel complesso e veramente di facile ed immediato utlizzo. La confezione robusta permette di conservarlo e proteggerlo nel tempo.

Hätte ich nicht erwartet, das Gerät wird einfach auf die Bohrmaschine aufgesteckt und schon gehts los. Es schneidet wirklich perfekt, leise und sehr genau wenn man es ruhig hält. Einzig und allein die Versorgung mit Ersatzklingen dürfte ein Problem werden, habe bislang nichts passendes gefunden.

si adatta ad ogni trapano avvitatore anche a batteria! soddisfatto anche se lo ho usato di continuo per due mesi non mi ha dato problemi!!! e facile da utilizzare anche se le istruzioni sono in altra lingua