DC 12V Self Priming Diaphragm Pump Fresh Water Pump 1.3LPM 30PSI

Works great! Ended up using the twister caps to splice the wires and it fit perfectly in my primo cooler. It comes with the adapter but in my application that was way too much unnecessary work to get to where it plugged in. Just cut the wires. Bit of a pain working around the coolant wires and such. Thin wires a pain to cut and splice for an amateur. I am stupid and didn't even need a new pump, the water container was completely frozen and so well insulated it never thawed. Now I have 2 functional pumps 😅TLDR Check and make sure nothing is frozen. Take the top off of the upper tank and let it thaw a few days. Wish I did this! The machine won't engage the pump when it's frozen.

This pump is almost an exact replacement for my Brio machine which the nipple broke on the outlet side of the pump. I wasn’t patient enough to trace the wires and take the machine apart any further than I had to so I just cut & spliced the wires instead of searching for the plug end of the wire….. which that seemed like a lot of work. Delivery was quick, instructions included, & new quick connect elbows & screws were included in the package. Would definitely rely on this seller & item if this need ever arises again.

Direct replacement for my brio water cooler. Good quality and super quiet. Easy to install, connector was same as factory. This pump is quieter than the original pump too! I wish the wires were slightly longer, but I can’t complain I just fixed my water cooler for $26 bucks. Beats buying a $250+ new one. Don’t hesitate to try this one out 👍

Did not work or turn out to be a suitable replacement for my primo dispenser.

We bought this to replace the water pump in our Primo 601088 bottom load water dispenser. Original pump part # gmb-d-23130First: the plug that is on it works even though it's white instead of blue but it's wired backwards so you'll need to cut the wires and switch them to swap the red and black.Second: as others have said, the wires are shorter than the original. I cut the wire from the old one to lengthen it. I'm not sure if the wires could have been routed differently to eliminate that need but since the wires have to be switched anyway, i didn't bother to try.Instructions for the swap:Remove the 4 screws holding the grate on the back.Remove the 4 screws holding the black solid plastic panel on the top at the back.Remove the 2 screws holding the pump to the stainless sheet metal above itThere are 3 blue plastic retainer clips holding the water lines on the pump. Pull them out.Use a flathead screwdriver or the like to push the water lines off. The Grey piece stays with the white elbow. You'll need to use a little force to push it off, I couldn't pull it by hand.Follow the wires on the pump to the stainless box over to the right (looking at it from the back) - Remove the 2 screws going through the back.Unclip the blue plug from the boxCut about 8" of wire from the old pump.On the new pump, cut the wire in the middle somewhere.Strip all the wires and splice them back together either with butt connections or twist them and tape them with electrical tape - be sure to swap the red and black on one end when you do thisRoute the plug back up and reconnect it to the box.Reinstall the box with the two screws.Reconnect the water lines - the pump has an arrow showing the flow - be sure the arrow points to the line going up topReinstall the pump with the two screws - my water cooler had multiple holes drilled so you may have to move it around to use the correct original set - the bracket on the new pump does line up to the old one.Reinstall the top plate and bottom grate on the back and you're doneAs others have said, the pump is quieter than the original. I only installed it yesterday so I can't vouch for longevity yet.

I have been using this for a few months now and it is still working great. It runs all day from a 12-volt solar panel and regulator. I am using it to heat water in my greenhouse. It runs from around 8am to 6pm every day on sunny days.I would buy it again and I might because I am thinking about doing a second one.

I'm using this pump for an irrigation project for my garden. Ill give a video update later on in the season, but for now the pump seems to be exactly what I need for my project. It's well built heavy, not too big, not too small. I'm going to be feeding 50 drip irrigation emitters if not more later.

So far works better than the original. For my model Primo, the positive and negative were reversed, easy fix though.

A bit of work and my water cooler is back in service.Great little pump

Exacttly the same pump, easy to replace. Cable is like 1 inch shorter than original.

حلو ليس بتلك القوه

Arrived in Bowral in just a few business days - thank you Amazon and Aust Post.Pump is well built, good pressure and - for me, most importantly, super quiet !Replaced an original LG fridge water pump that would ‘wake the dead’

Llegó perfectamente. Esta bomba me llegó con todo y su arnés lista para conectarse. Hace muy poco ruido. Es mejor que la bomba que tenía mi dispensador.