Xitomer Tail Tidy Fit for Ninja ZX-6R ZX6-R 636 2019 2020 2021 2022 2023 2024 2025 Fender Eliminator Kits Compatible with OEM and Aftermarket Turn Signal

This fit perfectly and did not require modification, besides me cutting the cutouts to use my original turn signals. It is such a great price for what you get. Just buy it. I know it doesn't provide the hidden plate lookup like most people like, but it works well for what it is. It keeps the plate readable, but gets rid of that ugly tail.

This FE is perfect and awesome price. Added to my new 2022 ZX6R and used the existing blinkers. If you have after market (smaller) blinkers, this should also work as I had to break out the inserts for the OEM blinkers. (Easy). I may get smaller blinkers later but I’ll have to buy another one of these brackets. But at this price it’ll be worth it.On the 2022 Ninja, the servo motor is in the tail and it’s much easier to disconnect the 2 plugs for this install. Just make sure you disconnect the battery first so you don’t get any engine codes. Then make sure everything is plugged back in before re-connecting the battery.This looks sweet and took me about 2.5 hours. But I’m OCD so it can be done faster.This is well worth the purchase and a quality product. I’ll add pics in a bit. Gonna go ride first. 😎

The center hole is in the wrong place, I had to dremel out the center a little. Once done it looks good.

Fitment is excellent, install was super easy. You will need to cut the tabs where the blinkers will go. I was able to twist them until they snapped off. Only one side I had to sand down, since it didn’t snap completely. Other than that, everything fits perfectly.

It fits the ZX-6R KRT edition. Makes sure you use the spacers for your wires. Save yourself the money and buy it! It works fine!

They give you exactly 4 screws, 4 nuts, 4 spacers and 8 washers. NOT A SINGLE SPARE, VERY CHEAP!!!I dropped 1 nut and 1 washer somewhere inside the bike when I was putting the tail tidy onto the bike. I ended up securing the tail tidy with only 3 screws.Edit:I have bought some m6 nuts and washers to complete the install

Ordered this tidy tail bracket to clean up my bike’s backend. Decided on this version which retains the factory stalk turn signals. Previous bikes I’ve owned I always installed the integrated turn signal/brake versions, however, I was told by cagers who were following me that it was difficult for them to discern which direction was blinking due to the shorter distance between left/right signals on all in one brake/signal light versions. Also my 2021 ZX6R has LED lights standard including the turn signals and the license plate light so this was another reason to keep my stock lights.Regarding install, instructions weren’t included as advertised but beforehand I watched a install video that was for a bracket that was identical to this one and for the same generation bike that I own. So I went ahead and disassembled the stock bracket in anticipation of this bracket arriving later that day. Once the bracket arrived it took me less than 15 minutes to assemble the parts to the new one and completely install and buttoned up. I’m in no way mechanically inclined but this is definitely a “do it in your garage” type of job if you have the correct sockets and screwdriver on hand.I included a before and after picture with my review. For a fraction of what others charge for their comparable brackets, this is definitely a must buy if you are in the market of tidying up your bike’s tail.

Excellent product! Fits like a dream, stock lic plate light mounts to it perfectly. Highly recommended to all bikers. Looks better than any other aftermarket kit I’ve seen on the road. Built very well and will last a long time! Extremely happy with my purchase!! Also seller had this to me 3 days earlier than expected date.

Si queda bien pero tienes que hacer algunos ajustes y mejoras para que no entre el agua en temporada de lluvias, ya que queda un espacio considerable entre la base y el porta placa

Tel que décrit!

Excellent price, fit and finish. I like the way you can reuse the existing indicators and number plate light.Fitted a 2023 ZX-6R perfectly.Arrived super fast from the USA (one week), well boxed and packaged and inlcudes everything needed to install.- 1 x Fender eliminator bracket- 4 x M6 x 25mm Allen screws- 4 x M6 Lock Nuts- 8 x M6 washers- 4 x Aluminium spacers- 1 x rubber grommet- 4 x cable ties- 4 x lengths of heat shrink tubing- Metal file- Installation instructionsA few small notes on installation:You can use the included metal file to twist out the indicator tabs and file down the notches.Install the number plate light first, before the indicators. Use the included rubber grommet in the centre hole for the number plate light mount. Feed the number plate wire through the grommet first, before fitting the grommet into the hole. Reuse the existing 2 x grommets, screws and washers from the stock fender to fit the number plate light to the fender eliminator bracket.I opted to use a 22.5mm grommet in the square hole on top of the fender eliminator, where the wires feed through into the bike, for added protection of the wires and additional water proofing. I purchased this from Super Cheap Auto.Use the provided spacers. This allows enough clearance for the wires to not get squashed and allows the fender eliminator to sit flush.The indicator and number plate light wire plugs are all colour coded, so it's impossible to connect them incorrectly. Number plate light is white, left indicator is grey, right indicator is black.If you disconnect the exhaust servo plugs, there's two of them, DO NOT TURN ON THE IGNITION until they are reconnected. This will avoid getting an engine FI error code.It's a straightforward install, just take your time and use common sense.It looks great once fitted and is actually better in many ways to some of the American branded units that cost stupid money for such a simple contraption.