iCrimp Square Self-Adjustable Crimping Tools for AWG23-10 Bootlace End-Sleeves Ferrule, Ratcheting Wire Crimping Plier

Work as promised. Great ferrule crimpers (and no, autocorrect, they aren’t crumpets…). I just wish there were an easy way to modify it to be a bench tool. Next time I have 400 crimps to make, I'll simply buy this tool again and make it into a bench tool myself. UPDATE: Faced with the last 200 (of 400) crimps, I decided to go ahead and McGyver it into a bench tool, using stuff readily at hand: • Using two small-ish straight-blade screwdrivers on the 'static' handle, it was easy to release the clips holding the orange handle cover without destroying it. Removing this was necessary in order to retain full-throw to crimp completely when adding something to hold the tail end of that handle down. • A Romex staple holds-down that tail end of the static handle. • A coupla drywall screws with two 3/16" nuts for height provide left-right positioning near the business end of the static handle. • A short length of 20 ga. solid wire fed through the business end of the static handle is fixed to two drywall screws, and a 10 p. nail provides tensioning to hold the business end down and prevent slipping forward. • And, a small bar clamp holds the 2" x 4" down to the work bench. This project took about 15 minutes. Now, instead of beating up my hands, I can use the leverage of my whole upper body when bearing down. Made quick work of the remaining 200 crimps!

These aren't going to compare with Tyco or Knipex, but they work great for about 1/5th the cost. The crimp is good and the tool is solid.

Been crimping long before Vince and Howard. I've been using several methods but finally started buying up every crimp tool I have needed for my van converaion. I now have a large toolbox dedicated to just crimp tools.

I crimp ferrules on a daily basis--I used several brands at our factory over the years and like these the best so I bought a pair for my own toolbox--now I don't have to borrow other peoples. They make great crimps, and are comfortable to use for long periods of time, never jam. Well made and included 2 extra springs to replace should the original one wear out. Great deal for the price!

OK tool. Not wild about the square crimp.

This tool is simple to use, makes a good crimp and if necessary it can be adjusted which I had to do to crimp some smaller gage wires. It is well built and even though I only use it a few times a week, contractors in our facility have built huge panels using this tool with no problems. Considering the cost a person could afford to purchase two, keep one as a spare and the other for daily use.Compared to tools twice the cost that only crimp one or two sides of the pin, this is a quadruple bargain.

Used this crimper to install a two amp system in my 65 Corvette. I had to use different sized Furrels and had No problems. The crimps were tight. The only way I could remove one was to cut it off of the wire. Great little crimper!

Great value and functions well. The surface finish on the outer silver metal is a little rough in some spots -- pitting, not smooth. I expect more from a new product, but I expect I'll naturally add a lot more imperfections to the surface as I use them.

VeryGood working

good product.

使い方の取説が無い 一部の設定が出来そうな事商品紹介に書いて有りましたが、パッケージには外国語、更に何も書いてない入れて欲しい入れて欲しい つまり、極小から、極太まで対応している商品なので、太さによって、ダイヤルみたいのを動かす必要あるハズなのに、何も書いてない 東洋技研の工具を仕事で使用しているが、比べると雲泥の差がある。とにかく圧着するのに力が必要 堅い

works great would recommend this tool to anyone