Shop Fox D2274 Heavy-duty 5-Roller Stand

the fasteners were third rate at best and I think this is it's weakest link. that and a few were missing. they are m6x12mm and there is 20 per stand. get yourself some grade 8 or better bolts, and nylocks to go with them. when you put the feet on, you want to put the nuts and bolts on that are the furthest away from the opening, or you might not be able to get your fingers in there. This is rated for 250 pounds, but I don't think I'll put that much on there ever. I think real world I'd give it a hundred pound weight at most. Here's the good part; the feet are really stable because three feet always hits just right. the rollers are nice and big, so things roll over them easy, and don't tend to get caught on anything. there's a little bit of flex in the roller table, so if you are off slightly, it's OK, it'll self adjust. and at the price point, you can have one for infeed, and one for outfeed. And here's why I bought this set in the first place - it reached high enough to work will all of my tools. the others that I looked at were all too short. so this will work with my full size table saw, full size bandsaw, and full size planer. so there's some good, and some that could be better. I have a feeling these are going to be loads better than the hf ones I had.

I bought this 5 roller roller stand because it was used and around $50..alot of bolts were missing its scratched pretty good but for the money diffrence it's ok..it's not solid it's flimsy but not horrible..for what I do it works fine. Wish it had casters but it's ok. I would buy another for the same price but not a new one for regular price..

I rarely write reviews for products unless they are exceptionally good or extremely bad. This is the worst product I have ever purchased on Amazon. I not only wasted time putting it together but also taking it apart to return it. The stand is so flimsy that it would be useless for even a couple pounds loaded on it much less to be described as heavy duty. A stand made out of legos would be better than this. This item should be discontinued until the quality is significantly improved.

This roller is rated for 250 pounds but I can flex it by pushing on 1 corner with 2 fingers. I wanted the stand to support 3/4 inch plywood sheets so I could feed them onto my table saw. It would not support my table saw sled while I was trying to level it to the table saw.

Good quality, but be careful of the adjustable height lever mechanism. This part of the stand is poorly designed and I had to replace the 1st unit I ordered. To avoid a repeat of this, I leave this stand at one height. I f you plan to change the height frequently, I'd look for another stand.

Cheap Chinese construction, poor instructions and mediocre quality. However, works fine as an inexpensive outfeed for light duty table saw work.

I have a couple of Shop Fox single roller stands and they are just fine. This product is built much more cheaply. Hard to get it level and I don’t anticipate it being very durable.

It'll do the job but it seems kinda chincy, not sure how long the locking or tighting knob will last the top part seems kinda heavy for the 1 bolt to keep it from dropping down . Also don't like the cancer warnings on this .

Parfait pour couper seul des feuilles de 4x8. Solide et efficace. Après avoir coupé plus de 10 feuilles d’une épaisseur de 3/4’’ le support a garder son ajustement

The roller stand is a bit overpriced for what you get. Mine arrived with the box intact but once opened I found some of the chrome on the rollers flaking off. There is a parts list but no real assembly instructions included. It was somewhat difficult attaching the feet to the base as you have to put the nuts on the bolts without being able to see them and balance the support rod while you’re doing this. Make sure you have a good large work surface, and if possible a vice or some other device available to hold the support rod in place while doing the assembly. Once assembled it looks fairly solid but I am not sure about how much weight it will support.

I have purchased many other Fox Shop products, and most of them were very good quality, but this definitely isn't one of them. As many other reviews have pointed out, to call this roller stand "Heavy Duty" is just false advertising, and very misleading! Also, if you are going to ask for $130 or more it should really be "Heavy Duty".I think Fox Shop would do way better by simply marketing this product label as "Light Duty" with a maximum roller stand capacity of 75lbs, and reducing the price to well below $100.I think they would sell a lot more of them to those that don't have the 250lbs capacity requirements instead of trying to mislead people into buying this roller stand!

This is such a great tool. No longer do I need another person to Hole wood while cutting

Great for the price. Rollers run smooth.