MEAN WELL LRS-100-24 AC/DC Switching Power Supply 108W 24V 4.5A Single Output for 3D Printer, Lab Equipment, LED Stripe and Industrial Applications

I have had great luck with this power supply. Reliable and quiet. Power seems to be steady. I would buy again and recommend.

Mean Well is known for their quality. I bought this for a 12V garage installation to keep all my batteries at full voltage, and needed high power in a small package. This delivered perfectly. It also handled a short circuit with no ill effects. The output is adjustable, and I set it for 13.2 Volt, perfect for car batteries.The website has documents for both UL listing and CE listing, so this is safe and approved for use pretty much anywhere.

OK, so I was a bit leery about a switching supply from China that was this cheap since I had had birdies before with switching supplies on my HF gear. This seems to be working fine! I don't have any detectable birdies, and have used it on all HF ham bands. No complaints about the power! I do wish that they would include the mounting clips and screws. Just know that you have to get both separately.

Shipping was on time as expected, and on a Sunday! This is the direct replacement part for my Creality Ender 5 Pro. I think we had an intermittent-sketchy power outage and it killed the original power supply, per good AC input, but no 24V output. So I get this one and I have been back up and printing for a full constant week now. I'm sure it'll last a long time.

Voltage was steady, the measured AC component was 0.0000 V on our Fluke multimeter, although this wasn't with any load in place. On the whole this appears to be a good, low noise power supply.

Seems to be a good little power supply. In the first tests it did just what I needed, which is to run a small 12 volt, 3 amp water transfer pump. Output rated 12 V, 6A, Measured 12.5 V no load and 11.7 V at 6 A, which is very good. I did not measure noise or AC components, don't care here. One star off because one corner of the aluminum mounting frame was bent, probably from being dropped at some point. It was delivered in one of the new thin plastic bags, but I did not see any damage to the thin inner cardboard box, so I don't think it was a delivery problem. I can straighten it. Very prompt delivery.

I have three older 17A Mean Well power supplies that have been excellent performers. I needed 25A or more for my new ham radio (Yaesu FT-710) so I ordered this one. When I got it, I thought they shipped the wrong item... it's a lot more compact than my older 17A power supplies.I added a power cord to the power supply (you have to provide your own three-prong power cord) and hooked up my radio. No line noise was detected (I do have a single clamp-on mix 31 ferrite bead on my radio's power cord). Nice!

I purchased this when the fan on my 4 year old stock PSU started getting pretty loud and the love tap to quiet it was getting less effective. I swapped the fan on it and it worked - but several forums recommended upgrading for more stable power.This installed pretty easily - the biggest con being that I needed a new lower cover. I ended up printing an adapter piece which worked great.The best part of this PSU is the demand fan - it turns on when it senses it is needed and my fan was pretty quiet. So, my printer is quite quiet now - with more stable power.

Just do it if you have a cheap power supply in you 3d printer like the sovol sv06 and plus model.

Excellent power supply

Working fine. Performance as per spec. Output is very clean, free of spikes and noise. Rated for 6A but can go upto 8.4A before entering hiccup mode overload protection. Default output voltage is 12.07 volt. Voltage didn't drop at the terminals i.e. remained at 12.07 volt upto 8.4A. Voltage can be set between 9.85 to 14.20V. So overall initial performance is excellent. Let's see how it performs in long run.

The real deal. Works as expected.

Serves my purpose.