AmeriLite Chrome 1pc Replacement Headlights Corner Dual LED Halo Set For 01-11 Ford Ranger - Passenger and Driver Side

I got to say, when I bought these I was a little skeptical, but the quality in which they are shipped in and how they perform are great. Installs easier than the removal of the old ones. I have a 2006 ford ranger and these lights sure do produce some serious lighting from the halo's. Easy to wire together if you have a multimeter and some scotch locks. I would recommend these lights to anybody that drives in really dark and windy roads, like I commute in. The only downfall I have with these, is the top of the headlight there is no weather strip to allow the rain/moisture from getting in through the top, but you can get some at Autozone and DIY this remedy yourselves. Other than that, these lights are clean and appealing to see.

A clean install and they look amazing. The halo ring lights really make a difference.some modding is required with the daytime running lights in order to get all the halo LEDs to work. If you're installing on a Ranger there's a space below the headlights that's open That's a good place to put pretty much all of the other LED circuitry.Just make sure wherever you choose to mount or reroute the LED circuitry and daytime running lights, that they are either cemented or double-sided taped in place so they don't move around during the drive.

Most people buy new headlights because their others are faded and sun bleached, so make sure to wax these headlights regularly to keep them protected from the debris and UV light to stay pretty! I personally have absolutely nothing bad to say about these. I was pretty rough on installation by hitting and pulling aggressively and nothing broke which is rare nowadays with everything else being mostly chinese junk. It was my truck that is out of line not the headlights. These are exact of stock headlights, I compared side by side just to check. The halos are power and ground wire, which I thought was great because you could choose how you'd like them to work. I spliced them into my daytime running lights. It felt expensive to spend the money at first but when I opened up the box I felt like I got a steal, everything was very well made, looks expensive, and it came sitting in specially molded shipping foam. I highly recommend this product, and if any issues arise down the road, ill report back to this comment.

These headlights are a good product. Fit into my 2001 ranger perfectly and look great. The halos are very bright and look really good in my opinion. The only problems I have with them is that there needs to be some kind of wiring instructions included. I found it pretty easy to figure out and do, but not everyone is mechanically inclined. Also the turn signal fixture that comes in the light did not connect with the plug in my truck. I had to use the fixture out of my old lights and do a little modification to get the fixture to fit in these headlights. Also the adjustment for the lights is nearly impossible to get to. I could not get a wrench on it. Had to improvise to move the adjustment. Overall though they are a nice product that looks good and does what it's supposed to. I would definitely recommend.

The media could not be loaded.  Pretty nice product.

Lights are nice, halos are very bright. However, took three hours to install, multiple modding situations, amber bulb’s wiring harness didn’t fit. Halos didn’t work without extra splicing to parking lights.

Installed these on 2003 ranger edge, it was very easy and the plugs matched up perfectly. You basically pull two tabs, unplug wires and remove old one, plug in wires, slide it back in and lock tabs. All done.

2002 Ford Ranger 4.0LTook me a couple hours to install. I had to make some minor adjustments to the lower mount and had to use the original turn signal plug-in (slightly modified). And of course the LED halos had to be spliced in, I chose the parking lamps. They work, look amazing, tho the led lights are a bit bright. The headlights are tough to adjust after installing, recommend using a flex head 10mm ratcheting wrench.

The lights are aimed to low, the only project a short distance. Tried putting PIA bulbs in, still drive with high beams on, and nobody flashes me. Save your money.