Oneplus 7 Pro/7T Pro Tempered Glass Screen Protector,Fingerprint Scaner 3D Transparent Clear Full Curved Edge Case Friendly Anti-Scratch Coverage for Oneplus 7 Pro/7T Pro 5G【2 Pack】

Great screen protector. The fingerprint scanner doesn't have any issues, it covers all of the screens, hugs the curves, works perfectly with my case, and is just very high quality. So I highly recommend.That being said, I had a few problems installing it. And to note, I'm a crazy perfectionist when it comes to installing screen protectors so take my issues with a grain of salt. The process seemed pretty simple: you clean the device, put the glue down in the center, and it works perfectly. This isn't exactly how it went down for me. So, I spent about half an hour stressing, watching videos, reading and rereading the instructions because I really wanted to do this perfectly. I cleaned my phone, put the glue in the center and waited. However, for whatever reason, when I did this there were tons of bubbles in the glue. So despite all the instructions saying to just let it sit and not to touch it, I decided to press all the bubbles out towards the edge of the screen to get rid of them, and it worked. After I used the light to dry it, I noticed that I'd placed one of the stickers used to keep the glue out of the font speaker to low and there was a tiny gap at the top of the protector where the adhesive never touched the glass. It was a tiny mistake. But I still made the executive decision to completely remove that first screen protector and start over with the second (I also got to test the impressive strength and flexibility of that first screen protector after I removed it). The second installation went about the same as the first did (with me ignoring the "don't touch" instructions and clearing away the bubbles are I saw them). I also decided to just be super careful around the speaker and not bother with the stickers. There's a good chance that in my quest for perfection I overdid something or just worried problems into existence, so I don't hold that too much against this protector. In the end, it worked to perfection and I couldn't be more satisfied with my purchase.

So I'm out 30 bucks.I made sure to look up youtube videos, the attached video to this amazon page, and read the installation instructions thoroughly before doing anything. First attempt, it almost went great, except that the provided sticker that was covering the speaker got a small bit of adhesive on it. "No problem", I thought. "That's what the sticker is there for. To protect the speaker."In the provided instructions, it tells you to cure the screen, take off all stickers, wipe away any additional adhesive, and cure the screen again. After my first time curing, I tried to gently pry off the speaker sticker but the adhesive had already become attached to the protector and the top of it lifted up. This left me with a small white outline right below the speaker due to the protector not being attached to the screen underneath. Looked bad, but not too bad since it was near the top edge. In hindsight I should have left it there but I thought I could do it perfectly next time. "I'll remove the sticker and wipe away the adhesive before curing! That will solve this issue!", I naively thought.Second attempt, I followed the exact same instructions, got to the part where I put the adhesive (in a strip from top to bottom) on the screen and carefully placed the protector on top. The adhesive once again spread throughout the entire screen... except for a small bubble right in the middle. And there was when I realized I was screwed. Once there's a bubble, there's nothing you can do. Unlike other tempered glass protectors, if you were try to push the bubble away to the edge, you'll just get adhesive EVERYWHERE. No go. If you were to cure the screen first, that bubble is stuck there for eternity. Just... looking at you... tauntingly. I went with plan C, tried to lift the screen and reposition, but now that the adhesive was near the edges of the phone, it just slid right off, to the table underneath. Immediately went to DEFCON 1, threw away the protector and used my own alcoholic wipes to clean up the mess before the adhesive got into any buttons. (They only provide enough stickers for the speakers and charging port)And now I'm sitting here writing this review. With a naked OnePlus 7 Pro. No protection whatsoever... so yeah...In all seriousness, it just sucks this costs $30 and there is a high probability of failure during the installation process. If you're reading this and are still going to give it a shot, I genuinely wish you the best of luck. For the brief moment where I was using my phone after my first attempt, the protector felt amazing and responsive. Try not to get any of the adhesive on the stickers and, if you get a random bubble, my deepest condolences.

I really like the screen protector. It forms well to the curved screen and is simple to install. No issues with touchscreen functionality after install. The only downer is it is quite expensive compared to other screen protectors. But I would purchase again.Update:Increased my rating to 5 stars after I had issues installing a couple screen protectors the vendor offered me a replacement. This is by far the best screen protector I've used on the one plus 7 pro. The only issue being it is more difficult to install correctly. But I've already bought another pack and will continue to use as long as i have the phone.A couple tips for those installing:1. Make sure you have a level surface prior to applying adhesive and screen protector. I used a not so level surface once and the liquid didn't spread as well as i would have liked.2. After applying adhesive place the protector on and let the adhesive fill between the protector and the screen by itself. Do NOT apply extra pressure to get the adhesive to move this can create air bubbles under the protector.3. After applying adhesive and protector Do NOT move the phone until you have done at least the initial UV cure. Moving the phone can cause the protector to shift and create air bubbles under the protector.