141 Multi-Purpose Floor Adhesive, 1 Quart, Off-White

I picked up the DAP 141 Multi-Purpose Floor Adhesive for a small flooring project at home, and honestly, it exceeded my expectations. From the moment I opened the quart, I could tell it was the right consistency—not too runny, not overly thick—making it easy to spread evenly with a trowel. The off-white color was also a plus, since it made it easy to see where I’d already applied adhesive without being distracting. What really impressed me was the grab. Once I set my flooring in place, it stayed put with minimal shifting, which saved me a ton of frustration and time. I didn’t have to constantly readjust or worry about corners lifting while I worked. Cleanup was straightforward too; a damp cloth took care of minor smudges before it dried. After everything cured, the floor felt solid and secure, with no hollow spots or movement. For a one-quart container, it went further than I expected and covered my project efficiently. If you’re tackling vinyl, carpet, or similar flooring jobs and want dependable results without professional-level complexity, this adhesive gets the job done—and does it well.

Ok, this stuff works perfect for me. I understand some of the complaints as to why it might not work in some situations but for sticking flooring back down, bingo, this is the stuff. I don't do floor professionally or anything but this is the go to stuff for the guys I know doing it. Here is the quick way to get this stuff to work as intended and avoid your own horror story: 1. Yep, it's all in the prep. Isn't it always? The floor AND whatever you're sticking to it (tiles, laminate, whatever) must be CLEAN and DRY. These two things are super important. Clean means, no dirt, oil, paint, lacquer, dust, wax, caulk... nothing. The floor should be flat and smooth as well. This isn't always completely possible (flat and smooth) but do your best to do exactly that. You want the adhesion layer to be flat on each side. 2. Just when you are ready to put this stuff down, clean the area with denatured alcohol or the like to get it SUPER clean. Let the alcohol dry out, but it will have removed any cleaners you used in step 1 and give you an absolutely pristine surface. This step should not be skipped and the difference it makes is categorical. Remember to clean both the floor AND what you are sticking to it. Also, it's a good idea to clean your tool before use like your putty knife or whatever. 3. Use a little at a time, maybe put down no more than you can use in 10-15 minutes or so. Use a trowel if you're doing a big area, or a stiff bristle tiny brush or something if you're just doing a small repair. Because you have cleaned everything so well, you can just trowel out material as you'd like and you won't contaminate your bucket. If you didn't do this, make sure to wipe off the trowel each time you go back into the bucket to avoid moving containments to the bucket and making it's sticking power less effective the next time you use it. If you have extra on the trowel when done, just toss it. Don't try to save it. 4. You need to use a roller to roll down the flooring and squeeze out the extra. Clean it up quick style. Not sure what size roller, it really depends on the area, but you need to put some real pressure down. On large areas a 100 lb roller will do fine, but on small areas with small rollers you're going to have to press and get some weight on it. 5. Give it 72 hours to dry fully. Clean up with mineral spirits. A few factors to remember are it dries slower in humid environments. Keep the area dry. Blow a fan on it if you have to. Any water or cleaner let behind from prep will absolutely screw you up. It can be as simple as it takes a week to dry, or it just doesn't stick and you have to start over. I suspect most people with adhesion problems were either on dirty surfaces, pitted surfaces, or got some type of water or chemical intrusion (even oils from your finger can screw up small repair areas). Remember, concrete can cause moisture, so doing this at the right temperature is important. Good luck and I hope this helped!

I was nervous about buying this after reading a bunch of the reviews but after reading the review by bonnie I decided to chance it. I'm replacing a few floor tiles (vinyl) here and there and don't have any glue left from my original installation. This is exactly the same as what I previously used. The people who are having trouble with tiles moving and glue not drying are likely applying it too thick. I used a notched trowel to scrape this around, you will still see some of the underlayment but have thin lines of glue. The container I received had thick tape wrapped around the lid which kept it secure during shipping. Works perfectly, couldn't be happier with my purchase. As someone else mentioned, Goof Off is your friend for clean up!

I used this Weldwood Multi-Purpose Floor adhesive to apply some new laminate flooring to my kitchen area. I did purchase self-adhere tiles, but wanted to ensure they would stay in place well and for a longer period of time than they otherwise would with the peel-back tape adhesive. This container comes with full instructions on the back, along with some information regarding the types of materials that it best suits and a small graph regarding coverage dimensions. Note: before you begin, be sure you have something on-hand to either protect or quick-wash your hands. This is a very strong and sticky adhesive that is very uncomfortable on the skin. It is similar to wood glue in texture; thick and pasty and a sort of off-white/cream color with a slightly yellowish hue. The instructions note to spread the glue and wait a minute or so until "legs" can form when pressure is applied and released from the surface of the application. These "legs" resemble reverse icicles (apply pressure with the finger and lift; some of the glue begins to lift with the finger until the finger releases-at which time the glue sort of "stands," or has "legs"). It is at this point it is ready for your material of choice to be applied and to have the best grip possible. I have included some photos to show the texture: one showing a spread application over a foam plate, another demonstrating the "legs" as noted above, and one reflecting exposed glue that has adhered to the lid rim after use (it becomes rubbery); as well as some general shots of the adhesive itself, and the finished tile after application. Overall, this is a great product at a very reasonable rate, that stretches well over a decent area. I would buy again.

Works great

Good

It didn't dry. I was able to pull a 12"x24" tile after 12 days without breaking it. I looked up online to make sure I was using it correctly. I even asked my son-in-law for help because he had just layed tile in his bathroom (He used a different product)he could not figure out the issue either. One container came cracked.

Yes, it's a great adhesive, but awful to apply. What I need is an adhesive that can be applied BEFORE it's sticking properties take full effect. I'm sure there's a way, in professional applications, to do this, but I don't have a clue. Also, it's not readily soluble even with paint thinner and certainly not with water. Needless to say, if you use this, have a full box of disposable gloves handy. Getting it off your skin is not easy. My solution: use Liquid Nails or a heavy-duty Gorilla glue instead. Note that these comments are made by a non-professional and just from my experience.